RK962G0K3 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Salem, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bottom Heating element broke
Ordered the part on Fri. AM and it arrived Sat. PM! Could not believe how quickly it arrived. Husband replaced the old element and I am baking again! Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOE from WESTON, CT
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned Out Lower Heating Element
Unscrewed the old one and screwed in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Baldwin, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned heating element (no continuity)
Removed old part, install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Meridian, MS
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
240 Volt Bake Element Failed In Upper Oven
Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Silver Spring, MD
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
My 20+ year old bake element cracked
I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Roseville, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replace baking element
Turned off power at breaker and removed old element and replaced new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William M. from Towaco, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element went dead
Removed access screws from bake element cover, removed screws retaining wire connections on bake element, reverse procedure, and heat to burn off contaminants.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Houston, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven bake element broken
Took out the old (removed 2 screws holding the element to the back of the oven, disconnected the 2 screws attaching the electrical wires to the element). Decided to clean the oven with EasyOff. It took longer to spray this on, and then later wipe it up, than the repair itself. Reversed the procedure for the new element. A very simple repair - my wife is amazed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernie from Gualala,Ca, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old burner had burned out and broken
removed old element and installed new, and oven is up and working like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Sugar Land, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element burned out
Turned off the breaker. Removed 2 screws and pulled the element from encasement. Removed 2 screws holding the wires to the element.
Reversed the process to install the new coil.
Done in 10 minutes
Reversed the process to install the new coil.
Done in 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from kersey, PA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven element burned out
removed the element with 2 screws. disconected element with 2 screws. reversed order to install new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Litchfield Park, AZ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element would no longer heat up.
Shopped online for a good price for the heating element. Thw element came very quickly, very good packaging. Removed and replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Glenmont, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken Bake Element in Oven
Unscrewed face plate, unscrewed electric wires hooked to element. Cleaned out oven while I was in there...nice and clean now. Installed new element same way I took it out. Easy as 'pie'..which we'll be baking again now that the oven works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from West Springfield, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
burned out bake element
The repair was a snap! Unscrew the two small bolts holding the back of the element in place. Pull out the element so that the connectors and wires are accessible. Unscrew the two wires from the element. Remove old element. Place new element in oven. Attach the two wires to the new element (two screws), place the new element in position and replace the two small bolts that were removed at the beginning. All done. Best thing? This is a 20 year old oven, GE didn't even have the part I needed. You did! Thanks.
Was this instruction helpful to you?
Thank you for voting!