RF764G*T1 Hotpoint Range - Instructions

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

I removed the screw holding the tilt mechanism to the range top. Removed the clips holding the block together. Disconnected the two power leads on the old burner and replaced with the new burner. Closed the block around the leads. Screwed the tilt mechanism back to the range top and that was it!

Finding the replacement part on partselect.com was easy. The search feature brought me to a diagram of the bake element and offered precise grid measurements to assure me it was the correct part.

Be sure to completely unplug your stove before doing anything. The only tools I used were a small nut driver, a standard pliers and a flashlight (and a cushion for my old knees, ha).

Installation was easy, but you have to be very careful to not bend the little prongs were you attach the element to the stove wires... they bend pretty easily, so hold them tight or hold them in a pliers firmly but without crushing them. Drive the two screws to attach the element to the wires; then, drive the two screws to hold the element face plate against the rear of the oven, and viola, you're done!

Thanks, partselect - website, price, packaging and shipping were perfect! Also, I got several good tips from the feedback of other customers that were very helpful. That is a nice feature of your website and a good customer service.

Before you start, make sure the circuit breaker is not tripped, which can explain element not heating.
In my case, the toaster element was ok, which tells us that the oven is receiveing electric current.
1) Take the grills out so you have free access
2) Remove the door - this model just pull it up to let it free
3) remove the 2 screws securing the element on backwall of the oven and gently pull the element out
4) if you have a multimeter:
a) set it to AC, greater than 300 V
b) use your alligator clips, attach the clips
to the contacts of the element
c) briefly turn the oven on: expect to read between 230 and 260 volts
5) remove the screws securing the old element
6) install the new element;
7) secure the element back to the backwall
8) turn the oven briefly on and feel the heating element: should come warm pretty quic;
- Job done -

When you remove the screws securing the wire to the old element, make sure the wires are not cracked, or interrupted.

Otherwise, a real simple and easy fix.

Specs of this element are what I missed but here they are:
Resitence : 25.5 Ohms
Volts: 230 - 260Volst
Power : 2050 to 2650 Watts
The power depends on the voltage, so make sure you dont have it too low (less than 220 ) or too much (yeah, 260V is nearing upper limits)

Removed trim ring and drip pan, loosened retaining nut and replaced the burner. I was very impressed at the fast service from your company. Thank You

Removed two clips that held the ceramic insulators in place. Removed two screws that held conductors to the burner. Replaced screws onto new burner unit, replaced ceramic insulators. Fastened clip to burner onto the range. Turned burner on and it worked great. Thank you for your quick responce to my order.

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

Removed the plug from wall socket.
Removed door to oven by lifting it straight up while partially open, in locked position.
Remove Baking shelves.
Removed 2 screws @ the back of element where it goes into the ovens back wall with a nut wrench and gently pull the element towards you until wires are exposed.
Using a flat blade screw driver hold on to the end of the element near the end with the screw and support it as you un screw the wire so the end of the element does not bend as you turn the screw.
After both wires are removed, remove the old element.
Install the new Element in reverse.
Very Easy!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.

Replaced the burner. Still no heat. Decided to take the front off and test the connections (Power Off!). Found no output from switch to burner. Ordered new switch from PartSelect. Switch arrived in 24 hours, just like the burner (I'm in FL, but still fast!) My only problem was that the know didn't quite fit -- too long. Cut the metal correctly, but still too long. Had to cut the plastic adapter slightly. Now it fits like the others, but it's not quite as secure due to shortening the piece that slides on the metal shaft.

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.

The repair was pretty easy. I unplugged the stove and took the 2 screws out that secured the element into the back of the stove. I then used a pair of needle nosed pliers to pull the wires off the element that wasn't working and then attached the wires to the new element. I then put the screws back in place securing the element to the stove and it was done. It took me about 5 mintues and the element worked immediately.

unscrew two screws pull the old element out put in new one and screw back in . We had to wire it direct because our oven had quick connect connectors and this part did not. But it was no big deal and didn't take any time to fix.

The part arrived ahead of time by mail. I removed the old coil, very simple,, I installed the new one just as easy , Turned on oven and it worked prefectly , its a very simple procedure, thank you