RB636402 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- sharon from mt pleasant, NC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bottom heating element broken
I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from peabody, MA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
replacing old rusted drip pans w/ rings
simply lifted the heat coil and slid the rings off and lifted the drip pans off. Vacumed the bottom underneath the old pans. Cleaned the grease off around the stove where the rings sat. Let it dry and added the new rings and pans. Looks like it did 30 years ago.......let them try making a stove last that long today !! Make sure the power is OFF at the electrical box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carey from granbury, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
replaced element
(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Harvard, MA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The control knob stem broke off when I moved the stove.
I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ida from Ann Arbor, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
lower over burner did not heat.
I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Coleman M from Sedona, AZ
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken bake element
Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee Ann from Oklahoma City, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Coil burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from North Richland Hills, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
old element was not heating at all
removed it, ordered it and it only took 15 minutes to replace it.
I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.
Very quick delivery, within 3 days.
I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.
Very quick delivery, within 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Kempner, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls could not be cleaned
Replaced drip bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Madison, WI
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Burner was crappin' out after 20 years of service
Pulled out the old burner that was held in by a metal spring clamp. Pushed the new one in.
Good as new.
Good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yi from Miami, FL
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old surface unit was not generating heat
We just remove the old surface unit and insert the new one by hand. Thanks to PartSelect, we were able to buy really good quality part that works right away! It was a 26-year-OLD GE Stove/Microwave space maker, the parts were hard to find in stores. Thank you for selling this! All the best for your business!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Plymouth, MA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No or little heat from oven.
The repair seemed very easy, even before I attempted it. When I recieved my part it was very obvoius that this was my problem part. The old element was worn out(21 yrs old). Having Thanksgiving around the corner, my wife was happy we had a fix to our not ready to replace oven. I was very pleased with your website picture matching choices and the very fast shipping you offered.
Thank You RR from Massachusetts
Thank You RR from Massachusetts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from West Melburn, FL
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original parts lost or discarded by prvious owner
Just replaced drip pans and rings on stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Birmingham, AL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bake element was damaged
Removed the panel screws that hold the bake element to the back of the stove. Then I disconnected the old element from the wires. Attached the new element using the provided screws. Reattached the old panel screws to hold the new bake element in place. Works great.
The new bake element doesn't have an item number on it, so I kept the old element in a cabinet someplace in case I have to replace this one again some day. I've lost the model number for my very old GE wall oven, so without that item number I'll be in trouble.
The new bake element doesn't have an item number on it, so I kept the old element in a cabinet someplace in case I have to replace this one again some day. I've lost the model number for my very old GE wall oven, so without that item number I'll be in trouble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Corinna, ME
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Both 8 inch surface units burned out
Simply unplug old unit and plug in the new. Easy
Was this instruction helpful to you?
Thank you for voting!