RA513402 Hotpoint Range - Instructions

Replaced drip bowls.

simply lifted the heat coil and slid the rings off and lifted the drip pans off. Vacumed the bottom underneath the old pans. Cleaned the grease off around the stove where the rings sat. Let it dry and added the new rings and pans. Looks like it did 30 years ago.......let them try making a stove last that long today !! Make sure the power is OFF at the electrical box.

After receiving parts, was getting rims unpackaged and removing the old rims, then and installing the new ones. Extremely easy to do. No tools needed

Just replaced drip pans and rings on stove

lift stove eyes and replace

Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.

replaced

Cut the power off to the range, unscrewed the burner from range and pulled off the element and unscrewed the two screws

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

It was so easy to find the correct items on your web site and they arrived in a very timely manner. Perfict fit. Now I know how to get parts when I need them.

replace trim rings with the new shiny ones I got from parts select. Thank you!

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

Took coil mounting assembly off first, then removed or took apart one piece at a time until heater coil was removed. Then installed (with furnished screws)the new coil, following entire process in reverse. 10-15 minutes time.

A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)

It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.

As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.

Yours truly,

William Rush,

i removed the two screws that hold the element in place. i then pulled the element out and disconnected the two wires. then i connected the two wires and screwed the element back in place and now it works like new.