RB5252A1 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marlin from Nampa, ID
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven was not heating the way it should of done.
I double checked to make sure I got the right part.I looked at your video and then just did as you suggested. It was a easy fifteen minute job. Thank you for making this so simple to follow along with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Brookfield, WI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
lower ( bake) element burned out
Turn off breaker for unit! Use nut driver to remove old element,and replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Wells, ME
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls and trim rings badly stained and dirty
It was so easy to find the correct items on your web site and they arrived in a very timely manner. Perfict fit. Now I know how to get parts when I need them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lanny from KINGSLEY, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
my bake element sparked and shorted out
Unscrewed four screws, removed old element, replaced with new part, done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Kitty Hawk, NC
- Parts Used:
- WB32X10013, WB31X5014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace drip bowl and trim ring
The replacement drip bowl and trim ring fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Reynolds Station, KY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not heat
Removed the oven shelves. Removed two small screws in back of oven. Gently pulled out element to get to two other small screws connecting the element and removed them. Removed old element. Placed new element in oven connected the two screws to the element. Replaced two screws on back of oven. Replaced the shelves. That's all there was to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Wesley Chapel, FL
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced trim rings and drip pans
Simple replacement on an old "built in" range in good condition but drip pans and trim rings soiled beyond cleaning. Stove top, although 20+ years old, now looks like new. So glad to find parts were still available as "universal" replacement parts for the 8 inch burner do not fit. Delivered to my door in days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Alameda, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable)
We spotted a flame coming from the baking element in the large oven
The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura J. from Hammond, IN
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element was deteriorated
Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ida from Ann Arbor, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
lower over burner did not heat.
I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Kokomo, IN
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner not heating properly
1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Yukon, OK
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
old units did not fit properly, and looked aged
followed instruction that came with the parts. Looks great and was easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ellisville, MO
- Parts Used:
- WB44X5099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Lower Baking element stopped heating after a 1" section melted and burned at a bend.
I removed both screws to remove lower element, and measured it prior to ordering the replacement.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them from being pulled inside the back cover, as the bolts were attached.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them from being pulled inside the back cover, as the bolts were attached.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeanne M. from Oreland, PA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The bake element 'fried itself'' -- making a horrible electrical noise and flaring up -- before dying.
First -- and thank goodness I read some of these stories first or I would have forgotten -- I turned off the circuit breaker to the stove.
I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The stove is about 25 years old.)
That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!
I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The stove is about 25 years old.)
That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sharon from mt pleasant, NC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bottom heating element broken
I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!
Was this instruction helpful to you?
Thank you for voting!