RK777G1J6 Hotpoint Range - Instructions

Throughout, I took care to not rest my full weight on oven door, although it's hard to work with arms extended. Shut off power to oven at outside circuit breaker, removed both racks, placed trouble light on open oven door at left to illuminate back of oven. Tilted element up to get at bolts. Used 1/4" socket set to remove two hex bolts holding burned-out element's plate to back of oven, pulled it out 3" to expose wire connectors. Held connectors still with pliers in left hand (to not bend wires) while loosening/removing connector bolts with socket set in right hand. Took effort to loosen. Removed element. Wiped oven floor clean. Positioned new bake element in same place, again held connectors still with pliers (left hand) and tightened wire connector bolts with socket set (right hand), pushed element back to original element's position. New element came with screws, not bolts, so used magnetic Philips screwdriver to get screws lined up (tricky), tighten new element's plate to oven's back wall. Removed trouble light, restored power, set closed oven for "bake" and "350 degrees." Element glowed hot in 1 1/2 minutes, ta-daah!

I read your website repair testimonials by previous customers and used that advise to do the job. I liked the suggestion to use something to attach to the unattached wires so they don't slip back into the unit. I used two clothespins. I had one stubborn electrical connection to disconnect so it took a little longer -about 30 minutes. But it was a simple job to do and my oven works fine again. The item was delivered timely from the order date and packaged well. Thank-you!

My Husband did the repair while I wasn't home. He didn't bother to shut off the power even though he should have. He didn't electicute himself or burn down the house and the oven works great so I guess it was a success!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and made sure that there was no power feeding the element. Next I disconnected the two wires that power the element. I then removed the old element and replaced it with the new element. Tightened the screws but had to be careful on the second one and hold with plier as the first one bent a little as it was being tightened. Slid the element back after the connection screws were tightened and tightened the mounting screws. Reenergized and tested. The job went well - easier than expected...

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

First I turned the power off to the oven. Then I tried to take out the nuts holding in the element. One nut came off easily, the other one was rusted on, I had to use wd40 to loosen it. The project was easy once I got that nut off. I pulled out the element, which is connected to two wires. I took those screws out, connected the new element to the wires, re-attached the screws, pushed it back in, attached the nuts that hold the element in the oven. Then I turned the power back on and the oven works like a charm. I installed it the day I got it. I was surprised how quickly it was shipped to my house. I am so glad I repaired the oven, a new one would have cost over $800, I bought the element for less than $30, including shipping! It also sets a good example for my daughter. It taught her that her mom can repair things too, it's not just something men can do!

Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.

Removed the broken one by disconnecting the two screws , yellow and red wires and replacing it with the new part you sent me. Very simple.

Removed the two screws holding the mount and then reattached the two wires to the element.

Turn circuit breaker off.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!

P.S. Shipping was very fast.

First turned power off for oven circuit at the breaker box then removed two screws that hold element in place. Pulled element out, tested for current, then removed two screws holding wires to element. Took old element from oven and inserted new element. Reattached wires with screws provided, and pushed element into opening. Replaced two screws securing element to back wall of oven. Turned the circuit breaker back on then checked to ensure the oven was working.

1. Turned the electricity off at the fuse box.
2. Took out the two metal screws holding the element to the oven back.
3. Unscrewed the screws holding the element coil, pulled the element out some and disconnected the two wires.
4. Replaced the old element with the new one.

Shut the power off to the stove. Removed the screws and pulled the old part out. Replaced with new part from Parts Select.

Your service is excellent. I received the part within two days of it being mailed. The emails received from you were very helpful and also confirmed the transaction.
Thank you very much.

Shut power off to oven. Removed old element with socket wrench. Replaced old with new element, using socket wrench and new screws. restored power. That's it. Fortunately, old screws were not rusted. If they had been, would have used a rust solven.

Easy! Removed the screws, took out the damaged element, reversed the process with the the new element. I called in my order on Monday and Wednesday evening the oven was repaired! It doesn't get any better than that. Thanks for the great service.