RB6363A1 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rodney from Trenton, OH
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven stopped working
very easy--cut power supply 2 screws then 2 more on element quick and easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Gate City, VA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old and rusted rings and pans
lift stove eyes and replace
Was this instruction helpful to you?
Thank you for voting!
Old trim rings were rusted and soiled
Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Roanoke, VA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven would not heat
Same as you described
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erik from San Angelo, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench (Adjustable)
Upper oven of dual oven stopped heating
diagnosed repair by installing heating element from lower oven into upper oven, and it worked. Ordered proper replacement part and installed using tools above. No problem besides the tight space.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Scranton, NC
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
electric burner burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Easy has falling off a log!!!!!!!!!!!!
Easy has falling off a log!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Commerce Twp, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove element went bad
Purchased the element from Partselect online -delivery was great -installed the new element in less than 10 minutes - the stove is now 100% again
Great Service
Great Service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Vineyard Haven, MA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat.
First I turned the circuit breaker off, then I removed the two screws with a nut driver, that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires with a straight scewdriver.
Reversed the the above process to install new element.
Oven was 27 years old.
Repaired and operational in less than 15 min.
Reversed the the above process to install new element.
Oven was 27 years old.
Repaired and operational in less than 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Carrollton, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Bake element burned out
Opened Breaker box
Threw oven switch
Removed two screws on element plate
Pulled element out 3 inch and removed two screws holding wires.
Ordered element on Tue.
Received element on Thur.
Reconnected screws on wires and plate
Threw oven breaker
Baked a cake
Threw oven switch
Removed two screws on element plate
Pulled element out 3 inch and removed two screws holding wires.
Ordered element on Tue.
Received element on Thur.
Reconnected screws on wires and plate
Threw oven breaker
Baked a cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee Ann from Oklahoma City, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Coil burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from North Richland Hills, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
old element was not heating at all
removed it, ordered it and it only took 15 minutes to replace it.
I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.
Very quick delivery, within 3 days.
I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.
Very quick delivery, within 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Kempner, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls could not be cleaned
Replaced drip bowls.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Oil City, PA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Bake element burnt open
I disconnected the 240 volt supply by removing the fuses from the fuse panel. Next I removed two screws that hold the element in place with a nutdriver. Then being careful not to short or ground the wires I pulled the element out 3 or 4 inches and turned the oven control to the on position and tested for voltage, line to line then each line to ground to be sure the correct fuses were pulled. Turned the controls back to off. Next I disconnected the wires using the same nutdriver and removed the old element.
I placed the new element in the oven, attached the wires using a screwdriver backing it up with pliers to hold the connector on the element, then slid the element into position and installed the two screws in the back of the oven, then reinstalled the fuses.
Partselect shipped the order right away. I ordered Thursday evening and received the element Monday morning using standard shipping. I wasn't able to reference the oven by part number (it is a 40 year old GE oven) but their pictures and 1" grid made it convenient to pick the correct part.
In the past I bought the main control circuitboard for my Kenmore dishwasher, a door light switch for my refigerator, a turntable motor for my GE microwave vent hood, and an element for a Maytag oven. Every time I have ordered parts they were in stock as indicated and shipped right away and were the right part.
I placed the new element in the oven, attached the wires using a screwdriver backing it up with pliers to hold the connector on the element, then slid the element into position and installed the two screws in the back of the oven, then reinstalled the fuses.
Partselect shipped the order right away. I ordered Thursday evening and received the element Monday morning using standard shipping. I wasn't able to reference the oven by part number (it is a 40 year old GE oven) but their pictures and 1" grid made it convenient to pick the correct part.
In the past I bought the main control circuitboard for my Kenmore dishwasher, a door light switch for my refigerator, a turntable motor for my GE microwave vent hood, and an element for a Maytag oven. Every time I have ordered parts they were in stock as indicated and shipped right away and were the right part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Marysville, WA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
The bake element broke in half and did not heat after that
First I took out the oven racks removed two screws then I pulled it out a couple of inches to expose the wires and removed the screw. Put the new element in place and replaced the two screws put the wires back and replaced the two screws that hold the element in place.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Canal Winchester, OH
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Element had burnt out
First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!
Was this instruction helpful to you?
Thank you for voting!