JP6612C3 Hotpoint Range - Instructions

ordered new surface element and pushed in to conector turned on switch to test and works fine thanks

I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.

I simply pushed the new burner into hardware. I then tested it to see if it works. . .

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

I lifted the coils, removed the old bibs and replaced them with the new bibs.

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.

Replaced old drip bowls with the new ones. Very simple, no tools required.

All I had to do was remove old drip pans and insert the new ones. What a huge difference it made. It made my stove look so much newer.

Pulled the elements out and replaced the parts that were missing . Then replaced the elements.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

Had one burner that was completely out as the old terminal block had a broken contact. The other burner was intermittent and would arc when heating up. There are several slightly different size terminal blocks. I had a hard time re-inserting one of the old burners into the new terminal block but got it to seat. I put a new burner with the new block on the other one and it fit much better. Additional tools used were a wire stripper and a heat gun for the heat shrink. The stove works great now.

Pulled out the 8 inch surface element and then used a 1/4 inch socket to remove mounting screw for terminal block and pulled out block with attached wires as far as wires would permit. My range top does not lift up so I had to work thru surface opening but there was at least 10 inches of wire to pull out so it was not a problem. Cut existing wires at block, stripped 1/2 inch of insulation using my wire stripper pliers and wrapped wire ends of new terminal block and secured with wire nuts provided. Slipped on shrink insulation provided and applied flame from a hand held butane lighter. The instructional video on the web site was a great help. I may not have done repair without first watchng how easy it is. A cheap wire stripper is a great help. This supplier made it easy to select parts with fast delivery and complete the repair. Great source of appliance parts.

Simple repair. Easy to do. It was disappointing to receive replacement parts which were not ceramic terminals as depicted and described in words, but plastic and therefore will need to be replaced again soon. In addition the shrink tube was not large enough in diameter to cover the wire nut, both of which were provided with the replacement terminal. Part # PS232646 is not ceramic, but plastic which does not fair well in high heat applications.

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.