RB6281A1 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- carey from granbury, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
replaced element
(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darla from Cowgill, MO
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven wouldn't heat
Took the broken heating element out of oven. Replaced with new one; which was easy to do.
Turned on oven. It started heating immediately
Turned on oven. It started heating immediately
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Amarillo, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Old element had ceased to work.
I removed the two screws that hold the element to the back of the oven. Pulling the element out of the back, I removed the screws which connect the element to the electrical wiring. I placed the new element into position and reconnected the wiring. I made sure that the wiring and connectors were insulated with shrink wrap plastic, then pushed the new element into place. Connecting the two screws to the back of the oven completed the job. Toughest part, kneeling on my knees -- the part supplied fit like a glove and it works wonderfully well. Hint: measure the connectors to the wiring so that you order the correct length! (I didn't and had to reorder, but I am very happy with PartSelect.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Brookhaven, PA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burners were burnt
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gainesville, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element cracked and arcing
First I unplugged the oven from the wall. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The installation process was just as easy as the removal. Approx 10 minutes and I was cooking. BTW, the heating element was at my house the next day after ordering. Great service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry L from Plainwell, AL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
The bake Element burned into.
I have to tell you i got wrong partfirst it was my mistake I got on phone and the lady understood my problem and told me procedure of returning part I got the right partnext day. I watched the video on how to do the job,although O new how. The video was a wee bit off,from what was easy.The man doing the talk through repair showed detaching the connections and bending each one back s as to not go back inside there inclosure. The connectors were way short on this one .The only way to attach the element was to take off back cover and push them together back there. Took couple extra minutes ,but job don e Ps will be ordering something soon
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lancaster, SC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out.
Removed element and installed new element. Fit perfect, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Roanoke, VA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven would not heat
Same as you described
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erik from San Angelo, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set, Wrench (Adjustable)
Upper oven of dual oven stopped heating
diagnosed repair by installing heating element from lower oven into upper oven, and it worked. Ordered proper replacement part and installed using tools above. No problem besides the tight space.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Scranton, NC
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
electric burner burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Easy has falling off a log!!!!!!!!!!!!
Easy has falling off a log!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Commerce Twp, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove element went bad
Purchased the element from Partselect online -delivery was great -installed the new element in less than 10 minutes - the stove is now 100% again
Great Service
Great Service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Vineyard Haven, MA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat.
First I turned the circuit breaker off, then I removed the two screws with a nut driver, that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires with a straight scewdriver.
Reversed the the above process to install new element.
Oven was 27 years old.
Repaired and operational in less than 15 min.
Reversed the the above process to install new element.
Oven was 27 years old.
Repaired and operational in less than 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Carrollton, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Bake element burned out
Opened Breaker box
Threw oven switch
Removed two screws on element plate
Pulled element out 3 inch and removed two screws holding wires.
Ordered element on Tue.
Received element on Thur.
Reconnected screws on wires and plate
Threw oven breaker
Baked a cake
Threw oven switch
Removed two screws on element plate
Pulled element out 3 inch and removed two screws holding wires.
Ordered element on Tue.
Received element on Thur.
Reconnected screws on wires and plate
Threw oven breaker
Baked a cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dee Ann from Oklahoma City, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Coil burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from North Richland Hills, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
old element was not heating at all
removed it, ordered it and it only took 15 minutes to replace it.
I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.
Very quick delivery, within 3 days.
I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.
Very quick delivery, within 3 days.
Was this instruction helpful to you?
Thank you for voting!