RHV786*06 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Scranton, NC
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
electric burner burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Easy has falling off a log!!!!!!!!!!!!
Easy has falling off a log!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debby from Wimberley, TX
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Burner supports broke, no longer could use the burner
Cut the power off to the range, unscrewed the burner from range and pulled off the element and unscrewed the two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Woodlawn, KY
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat
i removed the two screws that hold the element in place. i then pulled the element out and disconnected the two wires. then i connected the two wires and screwed the element back in place and now it works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from High Bridge, NJ
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element ruptured and wouldn't heat
The replacement was easy: turned off breaker to range; unscrewed element from range top;opened ceramic terminal box; unscrewed element from range wires. Then I simply reversed the procedure, using the new parts. Easy to do and it only took about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Langhorne, PA
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Replaced Oven Broiler Element
Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from San Antonio, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element burnt out
removed old element rewired new element,turned back on power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD W from PISCATAWAY, NJ
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heating Element Burn Out
Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from Bullard, TX
- Parts Used:
- WB44X173, WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broiler element seperated / infinity element switch bad
These two repairs were straight forward and the repair does not need elaboration. The amazing aspect of this repair was that I ordered my parts and received them on the second business day without any additional charges. That was really fast ! Thanks Partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Houston, TX
- Parts Used:
- WB30X348
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Broken Wire
A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)
It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.
As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.
Yours truly,
William Rush,
It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.
As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.
Yours truly,
William Rush,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kurt from Cortez, CO
- Parts Used:
- WB44X195
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Element burned out and started to deform
disconnected power
remove oven racks and oven bake shields
removed two bolts from end bracket plate on element
carefully pull bake element partly out until the electrical wires are visible, remove two small screws, remember the side of element each wire
attaches, red is power black is ground.
, replaced new element in reverse order, reattach wires to element and snug tighten , not over tighten. Element worked
like new.
remove oven racks and oven bake shields
removed two bolts from end bracket plate on element
carefully pull bake element partly out until the electrical wires are visible, remove two small screws, remember the side of element each wire
attaches, red is power black is ground.
, replaced new element in reverse order, reattach wires to element and snug tighten , not over tighten. Element worked
like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Killeen, TX
- Parts Used:
- WB44X195
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The bake element started to crack and open in several areas.It was just a matter of time before it would of broken in half.
Turn the power of to the stove used a 5/16 socked and unscrewed the element from the stove. Used the socket to remove the wires from the element. Installation was easy make sure you hold the end of the elements where the wires attach so they do not bend when tightening. Everything is working and back to normal. Make sure you use the model number to get the correct part needed.Part select was the best and delivery was with in 5 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLARD from GLOVERSVILLE, NY
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
instructions could be better
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from york, ME
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
support uder buner broke
The repair was almost to easy. It makes me wonder how many times in the future I will be willing to now attempt a repair instead of waiting and paying much more to have someone else do it. I thank you for the easy to understand video directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mission Viejo, CA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
Broiler Element Burned Out
The repair was very eash. The replacement element fit perfectly and only involved removing two screws, pulling the old element out far enought from the bak of the oven to disconnect the wires held by two screws . Disconnecting the two wires and installing the new element. This is a 25 year old appliance and is back to working like new. One note, be sure to shut the power off to the range because one of the wires connected to the element remains HOT! even if the oven is not on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Bremond, TX
- Parts Used:
- WB30X342
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
heating element burned out.
Replaced 30 year old stovetop cooking element with no problems. Stovetop works great now.
Was this instruction helpful to you?
Thank you for voting!