RS776G301 Hotpoint Range - Instructions

I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.

First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws. I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.

It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!

The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!

First I took out the oven racks removed two screws then I pulled it out a couple of inches to expose the wires and removed the screw. Put the new element in place and replaced the two screws put the wires back and replaced the two screws that hold the element in place.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Installed the new element reversing the process above

First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!

Removed the oven shelves. Removed two small screws in back of oven. Gently pulled out element to get to two other small screws connecting the element and removed them. Removed old element. Placed new element in oven connected the two screws to the element. Replaced two screws on back of oven. Replaced the shelves. That's all there was to it.

Once I watched the video pertaining to the installation of the part, the job was very easy.

This is a forty five year old oven. It was only four screws and it was done. The new part works like a champ! This save me from buying a $800.00 replacement. I removed the two 1/4 screws holding the element to the back of the oven and then took the flat head screws loose from the terminals on the old element. I then put everything back as it came out; took less than 5 minutes and the part arrived overnight! Thank you again!!