RA5114J4 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
there were two sets of screws and we tried to use the smaller ones which didn't work.
I called a friend who is a locksmith and a handy man and he changed the burners for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Hamilton, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Shaft for burner control knob broke off
I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deon from Olympia, WA
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Element burnt out
The repair was easy once he read the directions. The part arrived about 4 days earlier than expected. Great company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Portsmouth, RI
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
burner warped, pan didn't sit right
It would have been easy, but the screws that came with the replacement burner were too long for the ceramic insulator to fit over. Had to grind down the screws fro 3/8" long to 1/4" long. After that, piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerri from nashville, TN
- Parts Used:
- WB32X10012, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip pans were disgusting.
Just an easy replacement. Problem was, I couldn't find the parts. The service and turn-around was fabulous!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from york, ME
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
support uder buner broke
The repair was almost to easy. It makes me wonder how many times in the future I will be willing to now attempt a repair instead of waiting and paying much more to have someone else do it. I thank you for the easy to understand video directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Zanesville, OH
- Parts Used:
- WB30X359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
burner shorted and had to replace
removed the rings , tilted the burner, removed ground screw and removed the 2 hot wires and ceramic guard. reversed the procedure I ordered the part Monday am and received it tuesday afternoon, standard shipping Excellent service I will use PartSelect whenever possible
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from Ogden, UT
- Parts Used:
- WB32X10012, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Threw away old parts!
Put bowl in and then slid rings around. Just like cleaning procedure. Easy. Thanks for your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Markus from Lincoln, NE
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plastic lid left on hot burner.
Turned off the breaker to the range. Turned on range to ensure no electricity was currently flowing to the range. Turned the range off and unscrewed the tilt lock hinge. Pulled the burner out to expose the wires. Popped the snap locks off the cover box and unscrewed the wires connected to the posts. Followed recommend directions to expose approx. 1/2" of new wire (this is what I used the knife for since I did not have a wire stripper available). Slightly cut thumb in the process (no blood, though). Removed old burner. Put new burner in place, re-attached wires to the posts and screwed in to place. Placed cover box back in place and secured using new snap locks. Attached tilt lock hinge using new screw that was provided. Turned breaker back on and turned on range. new burner worked great. Took about 20 minutes total. Wife was extremely impressed, mostly that I didn't electrocute myself. She now wants me to replace other three burners. No good deed goes unpunished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
exchanges burner
Everything worked great, the delivery took only 3 days! My stove is I guess 50 years old and it's working with you parts! Thank you very much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Falconer, NY
- Parts Used:
- WB48X67
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Only one rack in the oven
I thought I had founf "oven rack" on the parts diagram and I ordered it. It turned ut to be the wrong rack. I looked at the website again and found that farther along the set of diagrams there was a different style of rack with the little extra keeper-wire-prong features I needed. Two different diagrams and two different racks for what appeared to be one model. Service was excellent, no problem other than cinfusion w/ith diagrams and model numbers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Veazie, ME
- Parts Used:
- WB44X190
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replace Bake Element
No problem, remove screws, insert part, tighten screws just be careful not to drop the screws behind the oven wall.
Was this instruction helpful to you?
Thank you for voting!