4760 Hoover Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Could Not Use One Burner
Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabra from Dallas, TX
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost one of the knobs
Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alyce from San Antonio, TX
- Parts Used:
- WP715269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element quit working
Ordered the part. It arrived in about 4 days. Took a screw driver and in just a few minutes, it was working again. BINGO
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from East Greenwich, RI
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced the current warn-out grease filter
removed the old by pulling it out of track and replaced it with the new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Smithfield, VA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Existing knobs were bent & unreadable
Removed old knobs and installed new. No tools were required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Flippin, AR
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Over the years the numbers has worn off the knobs.
Fed-Ex delivered the package and within 10 min I had open the package, removed the old knobs and installed the new ones, My wife was very impressed with the ease of the transactionl. It is good to know that we can still get parts for our cook top even though it is 26 years old. Thanks for every thing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Seguin, TX
- Parts Used:
- 700855K
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Two burner switches had broken
Turn off elec. power at breaker box. Check twice. Removed burner switch cover. caarefull remove wires from switch, note with color to which terminal remove nut on switch replace new switch replace wires to switch, replace cover turn on power. ready.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Summit, NJ
- Parts Used:
- WP715269
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
electric bake element had a physicle break
First I removed the two screws that hold the element in place. Then I pulled the element out about 2 inches & disconnected the two wires, Then I removed the ground wire. I then wired in the new element ( this was the only tough part of the process, because I had a very tight space to work in- less than 2 inches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Anna Maria, FL
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new grease filter
Removed old grease filter,replaced with new grease filter. No tools needed.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.
I ordered the grease filter on Tuesday and it arrived at my door on Wed.
Best experience ever ordering a part, I will definitely use Part Select again and have already recommended it to friends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Jacksonville, FL
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
cooks "high" on all settings
Turn off the power. Remove 2 screws (in the blower compartment) and lift up the control panel. Release the switch by removing the fastnut. Unplug each wire from the old switch and place it in the cooresponding lug on the new switch. Screw everything back together and cook.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- A E from Houston, TX
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
One electric range top burner element quit heating
Kill power to range unit at the breaker. Remove 2 screws on back of center control panel. Lift control panel up and toward rear of unit. Unscrew retainer nut which holds switch in the control panel. Carefully note wiring connections, and unplug all 5 wires from switch with pliers. Remove old switch. Reconnect all wires to new switch. Reattach switch to panel with retainer nut. Replace control panel in range with screws. Turn on power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Rochester Hills, MI
- Parts Used:
- WP715269
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Heating coil/ element gave out.
I turned off the power first. Then I removed the element by taking out the three screws. The oven was quite old so getting the screws out took a little extra effort. Installation of the new element went easier. I was pleased with how soon the part arrived after I ordered it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Cottage Grove, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had to replace grease filter
Nice filter. Exact fit. Had a little ring to use to pull out to clean. Shipment was packed well.
Was this instruction helpful to you?
Thank you for voting!