4875 Hoover Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Medfield, MA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the original grease filter was worn and falling apart
Removed the old filter from the top of stove and put the new one in. Took about 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from WARRENTON, VA
- Parts Used:
- WP715269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lower element was burnt out
same as your example
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Leighton, IA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter broke
Lifted the old one out and put the new one in. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Lakeville, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The heat would not stay on keep heating up and turning off with no low heat
Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts
Was this instruction helpful to you?
Thank you for voting!
Both burners would come on when you turn on the back larg back burner.
Replaced surface unit infinite switch
Was this instruction helpful to you?
Thank you for voting!
stem on burner controls broken
follow the EASY to read and understand instructions.replaced all 4 controls in about 35 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Bedford, VA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter element missing screen material from age and cleaning
Lifter grill and replaced filter. It fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Cottage Grove, OR
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch post broke. Could no longer turn that burner on.
Replacing the switch was quick and easy. It actually took only about two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Cadiz, KY
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Knobs worn and bent
Placed new burner knobs onto cooktop. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Emporia, KS
- Parts Used:
- WP71002111, 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
one burner switch was broken
The part was a perfect match and the instructions clear. Easiest $75.00 I ever saved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Summerville, SC
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Off-on switch would not turn burner on
Turn off power to cooktop. Lift the broken infinite switch knob off the switch console. Use pliers to remove the hex nut that is under the knob. Then remove the grill over the exhaust vent to expose the two screws that hold the switch console in place. Using a philips head screwdriver, unscrew the two screws and lift the console up as far as the wiring will let you. Push the two little clips on either side of the electrical component you want to replace, to release it from its harness. Pay attention to the wires of the broken switch and pull one off at a time and attach to the new part. I used a knife to pry the wires off the electrical pins. Once all wires are reattached, clip the component into the harness and attach the hex nut back onto the protruding d-stem. Put all back together and test the switch before turning power back on. If ok, turn power on and test again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Athena from Mill Valley, CA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs were old and some settings had worn off.
Wrap first three fingers of right around old knob. Pull it off and throw in trash. Take new burner knob and slide it onto the stem. Repeat 3X, that is, once for each remaining burner knob. Time to complete job - 45 seconds. :-D
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from ROCKLEDGE, FL
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not read numbers on the knobs
Simply pull off the old ones and replace with the new ones. Problem was finding the correct knobs with the double "s" shaft fitting.The item number indicated by the model number was incorrect. I saw a kit with four knobs on your web site and ordered the kit and not the recommended item. Turned out to be the right move and the knobs fir just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Temple Terrace, FL
- Parts Used:
- 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heat Errosion
Wife installed them, they just snap into place on the Rock Grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Santa Claus, IN
- Parts Used:
- 700855K
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Surface burner did not heat
I ordered part one day, recieved part the next day. I installed it the next day. It worked perfect. THANK YOU!
Was this instruction helpful to you?
Thank you for voting!