S100 Hoover Range - Instructions

First we removed the two screws that hold the element in place. After pulling it from the back of the oven we did not realize that the clips that held the wires could be slipped off the 'tongues' of the element. Therefor we thought we had to cut the wires - which we did. After realizing that the clips came off, we went to the store and bought a box of new clips, stripped a small portion of the plastic on the wire to expose the wire and put it in the new clips and crimped them. Then slipped the new clips onto the new element, replaced it and put the old screws back. You wouldn't need to buy new clips (not expensive) if you know ahead that they can be removed from the old element and slipped onto the new one. We were amazed at how quickly the element arrived in the mail. Have bookmarked this sight for future repairs.

Took the (6) screws holding the top of the stove out, then removed the switch screws(2). Then lifted the top, so as I could reach and get at the switch. And then I repeated the above. It was alot easier the second time. Duh I erred the first time and replaced the wrong one and before I relized it, I opened the switch to check out. All in all. I still got satisfaction from doing it myself. Thanks Parts Select

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

First Inserted 2x4x 36" length of wood behind the spring loaded door hinges to ease removing the oven door as I worked alone (this was recommended in a previous post and was essential when working alone, TY). Removed 2 retaining screws on the interior side of the door at the hinge locations. Slid the door up an off the hinges, moved door to a cloth pad protected work bench. Took the door and glass panels apart removing all the related screws, retaining clips; taking note of screws, retaining clip and panel locations for reassembly. Removed the insulation, removed the glass window pack, and removed of all rust fragments (dust) between the 2 glass window panels. The glass window pack metal molding retainer, on the oven interior side of the glass window had completely rusted away. Removed the existing oven door gasket. Cleaned the glass door window pack, and interior side of the oven door surface. Installed the new gasket, which fit very well. Tightened the loose door handle screws. Reassembled in reverse order all door components noted above, and replaced the door onto the hinges, fastened the 2 door hinge screws, removed the 2x4x36" wedge holding the hinges in the open position, and closed the door. Job complete. Thanks to previously posted directions as a good guide. Hope this helps as well.

Fortunate to have the replacement parts available.
Wish a replacement door window pack was available, as the double glass, metal edge seal is deteriorating, and the metal molding retainer that held the glass in place is completely rusted away on the oven side of the existing window pack. Plan to find heat resistant caulk to seal the glass in the door, in lieu of the metal molding glass retainer.

Much to my horror, what was described as a simple, 15-minute replacement, took 3 days! In order to replace the oven door gasket, I had to disassemble the entire door. Every photo I saw of the gasket showed it as a flexible part: gently pull out the old one and push in the new. What I received in my order had a frame. In order to replace it, I needed to unscrew the door parts. Unfortunately, I made a few rookie errors, primarily because I kept thinking the next screw would release the gasket frame. So I neglected to keep track of the screws I removed, and I didn’t take any photos!
I must have used half a roll of masking tape to keep parts together; I did not have 5 hands! When I released everything and nestled in the frame, I had even more trouble replacing all the screws I took out. The majority of holes did not line up. So I just did the best I could, put in as many screws as I could. But after three days of working, I finally finished. It all held together, and the door did what it was designed to do. Really a repair horror. And I am not an incompetent novice!

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.

We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.

Replace filter

The hardest part of the repair was getting the old cruddy screws out of the old element. They were sort of "baked-in". Once we got the screws out the rest was really easy. Just inserted the element prongs & screwed the new ones in. Ordering & receiving the part was a snap...I would recommend your company to anyone. Thank you.

remove two screws, pull out element, diconnect two wires, toss old element,plug in wires to new element, replace two screws and viola- done

Now if you just sold faucet parts I'd be all set.

Unplugged and removed the old grill element by hand and installed the replacement element by plugging it into the socket. Tools were not required for this and it took less than five minutes. The new element is great and heats much better than the original did before it broke.

needed hammer to help loose screws .pulled out and replaced leement