4790 Hoover Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Harry from Bedford, VA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter element missing screen material from age and cleaning
Lifter grill and replaced filter. It fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Cottage Grove, OR
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch post broke. Could no longer turn that burner on.
Replacing the switch was quick and easy. It actually took only about two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Summerville, SC
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Off-on switch would not turn burner on
Turn off power to cooktop. Lift the broken infinite switch knob off the switch console. Use pliers to remove the hex nut that is under the knob. Then remove the grill over the exhaust vent to expose the two screws that hold the switch console in place. Using a philips head screwdriver, unscrew the two screws and lift the console up as far as the wiring will let you. Push the two little clips on either side of the electrical component you want to replace, to release it from its harness. Pay attention to the wires of the broken switch and pull one off at a time and attach to the new part. I used a knife to pry the wires off the electrical pins. Once all wires are reattached, clip the component into the harness and attach the hex nut back onto the protruding d-stem. Put all back together and test the switch before turning power back on. If ok, turn power on and test again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Athena from Mill Valley, CA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs were old and some settings had worn off.
Wrap first three fingers of right around old knob. Pull it off and throw in trash. Take new burner knob and slide it onto the stem. Repeat 3X, that is, once for each remaining burner knob. Time to complete job - 45 seconds. :-D
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Cadiz, KY
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Knobs worn and bent
Placed new burner knobs onto cooktop. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Emporia, KS
- Parts Used:
- WP71002111, 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
one burner switch was broken
The part was a perfect match and the instructions clear. Easiest $75.00 I ever saved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from ROCKLEDGE, FL
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not read numbers on the knobs
Simply pull off the old ones and replace with the new ones. Problem was finding the correct knobs with the double "s" shaft fitting.The item number indicated by the model number was incorrect. I saw a kit with four knobs on your web site and ordered the kit and not the recommended item. Turned out to be the right move and the knobs fir just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Temple Terrace, FL
- Parts Used:
- 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heat Errosion
Wife installed them, they just snap into place on the Rock Grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eliane from Potomac Falls, VA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
very old grease filter.
Very easy to replace the filter, nothing to it, take out the old filter and put in the new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from North Kingstown, RI
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the grease filter was no longer usable from too many washings
took it out and dropped in the new filter. Total time about 2 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MaryAnn from Scituate, MA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Simply replace the grease filter
Thanks for carrying this part for my old stove. And thanks for the great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Pembroke, VA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wanted to replace old grease filter
Removed old filter, dropped in new filter. A breeze! What was best of all, is that Parts Select shipped the filter immediately and it arrived within just a day or so! Well done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Warroad, MN
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter was old and discolored.
The new replacement grease filter came without damage and it was a simple task of removing the old and setting the new in it's place. No tools were required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from laveen, AZ
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace the grease filter
I lifted the grill off; took the old grease filter out and threw it away; placed the new filter in the well; put the grill back on. Wallah!!! just like new.
Was this instruction helpful to you?
Thank you for voting!