EG9-56W79 Hardwick Range - Instructions

First I removed the old bowls and replaced them with the new.

took old bowls out, put new bowls in, took a coffee break

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.

we removed the old pans after first removing the electric heating element and simply inserted tne new pans

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.

Purchased 2 piece broiler pan from this site

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

slide out upper protective sheet metal protector. it is loose and can contirbute to the element failure from door closing.

remove rear element screws,and upper support screws.
slide out upper element.

do not cut the wires, they contain mating plug to element. use pliers to pull apart the male-female
plug on element wires.

reverse procedure to install, use old extra screws on upper metal protector to prevent loose rubbing on upper element. there are holes for this no drilling required.

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

I marked all wires separately attaching a paper strip with tape to each connector and made a separate small chart where each wire should attach to the bottom of the switch. On this particular model there are three or four colored wires and two have both double and single connections to the same switch so the small chart told me where a single or double connector would attach even if I lost the attached taped information. Then since wires were marked separately, even if paper was lost I could still proceed with no outside help.
I had the luxury of leaving the breaker shut off while waiting for part to arrive. After arrival which was only a couple of days, I raised the stove top and let it rest on a small board maybe 1.5 feet so it would keep itself up.
The under assembly was already taken loose before so I just removed the broken switch taking all wires loose, which are already marked and replaced the switch with the new one. Gently placing each wire at its place after removing the tape for that connection. After all four wires were connected I held the switch up in place while screwing the two set screws into place. Then reattached the bottom assembly cover and then let the top down and reattached the four screws, one in each stove hole to attach the stove top to the under assembly. I then reattached one element and flipped the breaker switch on. No sound or problems so I tried the element and all is well. Reattached all elements and the project is done. PartSelect.com made this repair easy and economical. Replacement would have been 4x the part and shipping. Thanks.