CPG9841A689DQ Hardwick Range - Instructions

The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!

removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com

I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .

took oven tray out and loosened igniter and replace same works great.

Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!

Same as the other entries in this section.
The only thing I would add is a hint for removing the broiler igniter. As you can see from the oven igniter, the wires connect with a plug. For the top igniter, the broiler, the plug goes through the insulation and then through a hole in the rear panel of the oven. So, when you pull on it, you will think it is stuck or the wire is pulled taut. That is because the plug hangs up on the rear panel.
Stick your finger through the square hole that you can see inside the oven, and follow the wire through the insulation. You will feel the small round hole in the back. You have to wiggle the wire up and around a bit to get the plug to fit through the hole. Then you will have the slack you need to change the plugs.
That way, you don't have to pull the whole oven out and break all the caulking seals.

it was so easy my wife could do it!!!!!!!!

1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.

I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.

Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

removed door (pull up and out), removed all racks and bottom of oven, removed two screws holding old igniter, unplugged old igniter from harness, mounted new igniter using two screws and nuts purchased from local hardware store, plugged new igniter into harness, replaced bottom of oven and trays, slid oven door down over hinges. Oven works properly. Thanx!

remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.

First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took about 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)

My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then, somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!