EPD9-79KW659A Hardwick Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Toledo, OH
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner Would Not Heat
One screw taken out, 2 wires switched, new part & screw put in. Burner like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dicky from mcrae, AR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace burner coil connector
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Versailles, IN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
large burners not working
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Kay from North Charleston, SC
- Parts Used:
- W10196406RW, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner coil was falling apart.
Used new plug in coil burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from kent, WA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blair from Edmonds, WA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burned out surface element
I pulled the old one out and installed the new one. Never broke a sweat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Tigard, OR
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
failed heating element
Took out of package and plugged in. turned on. It took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Goodlettsville, TN
- Parts Used:
- WPY04100166, WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My burners were replacements that rocked and were uneven.
I unplugged the old ones and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Chesapeake, VA
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The surface burner socket that the burner plugs into melted.
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alison from Carnation, WA
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The drip pans needed replacing.
Put in the new drip pan -- which are really nice shiny ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delroy from Miramar, FL
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drip pan were burnt out
simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Carnegie, PA
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty drip bowls
Just remove old bowls from range top and put new ones. That is all ... just super simple! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Carnegie, PA
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty drip bowl
Remove old drip bowl from the range and put a new one back.
Was this instruction helpful to you?
Thank you for voting!