Models > EPF9-81KS9A > Instructions

EPF9-81KS9A Hardwick Range - Instructions

Jump to:

All Instructions for the EPF9-81KS9A

Customer:: Dennis from Oak Lawn, IL
Parts Used:: W11122006
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Burner was always in high temperature.

Pulled the range away from the wall and took out all the screws of the back panel. I had two different screws. Removed the dial and took two screws out behind the dial. Carefully removed the wires and placed them on the new switch. Screwed switch to panel, replaced dial and put the back panel back on range. Pushed range back into place.

Was this instruction helpful to you?

Customer:: Robin from Vanderbilt, PA
Parts Used:: WPW10245259
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

I had a power serge and it burned the Plug at the termial block and melted a few wire.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Was this instruction helpful to you?

Customer:: Deborah from Hodgen, OK
Parts Used:: W11122006
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Burner stayed on "high", could not adjust heat

I UNPLUGGED STOVE, removed panel covering the controls, removed the knob on front and the two screws there that hold the control in, inserted new control and replaced the two screws on the front that hold it onto the stove, used needle nosed pliers to unplug one connection at a time from the old control and onto the new control in the back. When I had all connections plugged onto the new control I re-installed the panel cover with a screwdriver, plugged the stove back in, and the burner is now working good as new!

Was this instruction helpful to you?

Customer:: Dennis from Oak Lawn, IL
Parts Used:: W11122006
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Burner was in full hot.

Turned off the power. Pull the range away from the wall and removed the eight screws holding the cover in place. Carefully pulled the wires off the old switch. Removed the old switch and replaced it with the new. Put all the wires on and replaced the back cover and was done. Burner works fine. This part replaces a lot of different number switches.

Was this instruction helpful to you?

Customer:: Jennifer from Albion, NE
Parts Used:: WPW10196405
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins

Drip bowls tarnished.

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

Was this instruction helpful to you?

Customer:: Jeremie from Freeland, WA
Parts Used:: WPY04000041
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Easy installation

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

Was this instruction helpful to you?

Customer:: Max from Bothell, WA
Parts Used:: WPY04000041
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven would not heat up properly to set temperature

The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced with a new one.

Was this instruction helpful to you?

Customer:: Matthew from Chippewa Falls, WI
Parts Used:: WP7803P058-60
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Broken Door Spring

Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to replace the springs. This job was very simple and easy.

Was this instruction helpful to you?

Customer:: William from Florissant, MO
Parts Used:: WPY04000041
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

The original bake element burned out

1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.

Was this instruction helpful to you?

Customer:: Elsie from Garner, NC
Parts Used:: WPW10196405
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

needed a new drip bowl and couldn't find ons that fit exactly but you had it

I removed the old one and put in the new one. Works great!!!!!!!!!!!!

Was this instruction helpful to you?

Customer:: ROSARIO from MESQUITE, TX
Parts Used:: WPW10196405, WPW10196406
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

To Old Needed To Be Replace

Actualy I just removed the old ones and replace them with the new ones . And thank you for your prompt delivery I found some one I can trust . Thanks again . Mrs bolanos

Was this instruction helpful to you?

Customer:: Stewart from Hanover, PA
Parts Used:: WPW10196405, WPW10196406
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

rusty pans

simply remove the old and install the new; perfit fit

Was this instruction helpful to you?

Customer:: Robert from Wilton, CA
Parts Used:: WPW10196405, WPW10196406
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

I needed to replace my burner pans.

The Drip Pans are a cinch to replace with no tools necessary. The best part is that the Web Site is extremely easy to use, and the parts arrived two days after being ordered.

Was this instruction helpful to you?

Customer:: Erica from Ivyland borough, PA
Parts Used:: WP660532
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

replacement of heating element for elec. stove

plugged it in to the spot where missing element was.

Was this instruction helpful to you?

Customer:: Robin from Seneca, SC
Parts Used:: WPW10196405, WPW10196406
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Drip bowls were all rusted.

Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!

Was this instruction helpful to you?

All Instructions for the EPF9-81KS9A