GBP26AA0 Glenwood Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Lansing, MI
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Perth Amboy, NJ
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lake George, CO
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right front gas burner ignitor wouldn't spark
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Las Cruces, NM
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
two burner ignitors would not function on cook stove
1. ordered two new switches
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from WESTFORD, MA
- Parts Used:
- Y07623602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
top oven gasket replaced
shortened gasket for this oven. moved hook approx. 1 inch. used high temp adhesive. simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Mt Kisco, NY
- Parts Used:
- Y0310525
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a new knob
Just perfect! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michelle from mora, MN
- Parts Used:
- R0711030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
oven thermostat broke
first i shut off the gas, then diconnected the gas lines that go to the thermostat itself, then i took out the 2 screws that hold it in place, and removed it completely from the stove. then i put the new part in place of the old part, and hooked it back up. turned on the gas, checked for leaks with soapy water, then ajusted the piolet light screws, lit the piolets and tested it out, workd better than new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Oxnard, CA
- Parts Used:
- Y07623602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace top oven seal
This is a simple replacement. The hardest part was that I had to shorten the seal because it comes 15 to 17 inches. So it needed to be shortened to properly fit. I cut the seal to fit, then took the metal hook on the end and super glued it to the cut end. I put a weight on it to make sure
Was this instruction helpful to you?
Thank you for voting!