Models > GBP26AA0

GBP26AA0 Glenwood Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
This is a genuine OEM replacement part. This surface burner ignition switch is commonly used on ranges, wall ovens, cooktops, and microwave oven combos. When the gas burner valve is pressed this is th...
In Stock
This piece of oven door seal has a metal hook on each end. This seal is compatible with the top and the bottom of the oven door window.
No Longer Available
This OEM replacement part has been sourced from the manufacturer. This control knob is used on ranges and cooktops to control surface burners. This knob is made of plastic, and it has a metal faceplat...
No Longer Available
No Longer Available
This single oven door side seal is fourteen inches long. It is made of black rubber and it has a metal hook in each end.
No Longer Available
This round gas burner grate is black in color and has a diameter of just under seven inches. This burner grate is intended for use with Amana brand gas ranges.
No Longer Available
This gas oven thermostat has pre-made holes right through the body of the thermostat so that you easily mount it horizontally. This thermostat has a 36 inch capillary tube and it allows for temperatur...
No Longer Available
No Longer Available
No Longer Available
Special Order
No Longer Available
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for GBP26AA0

Viewing 1 of 1
Will Not Start
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Richard from Lansing, MI
Parts Used:
WP4157180
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that atta ch to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Perth Amboy, NJ
Parts Used:
WP4157180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Lake George, CO
Parts Used:
WP4157180
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Right front gas burner ignitor wouldn't spark
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!