GAE26DM-0 Glenwood Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Irina from Green Cove Springs, FL
- Parts Used:
- W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ugly looking drip bowl.
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Phillipsburg, NJ
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wire broken off plug in block
Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Toledo, OH
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner Would Not Heat
One screw taken out, 2 wires switched, new part & screw put in. Burner like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dicky from mcrae, AR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace burner coil connector
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from Rio Rancho, NM
- Parts Used:
- WPY04000035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old surface element burned out.
I ordered and received the replacement element, then unplugged the old one and plugged in the new one.
Job done.
Job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Versailles, IN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
large burners not working
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosibel from Houston, TX
- Parts Used:
- WPW10196405, W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the old bowls were burned.
really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Two Harbors, MN
- Parts Used:
- WP74011243
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bad control switch for stovetop burner
Move stove away from wall to allow working on back of stove. Unplug stove. Remove metal cover from top rear of stove. Pull control knob off of control (front of stove) Remove 2 screws holding infinite control in place (front of stove) Replacement control not identical to original control, having more terminal lugs and different physical arrangement. I used the terminal letters as a guide for placement of wires. The letters were not exactly the same, but close enough. Re-attach control to stove with 2 screws. Re-attach back metal panel to stove. Shaft on replacement control is smaller diameter and different shape from original, so I removed ribs from inside of control knob hole and then squirted a small amount of hot glue into the hole. Smearing a small amount of cooking oil onto shaft of replacent control I then slid the control knob onto the control shaft, holding it in place until the glue cooled and set. Plug stove back in, and return stove to its position next to the wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Chesapeake, VA
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The surface burner socket that the burner plugs into melted.
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Arlington, TX
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed to replace to two 8* drip bowls on the kitchen range
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gizella from mays landing, NJ
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dirty drip pans
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Staunton, IL
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner keep coming on and going off had a short in burner plug-in block.
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from kent, WA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Union Mills, NC
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Oxnard, CA
- Parts Used:
- Y07623602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace top oven seal
This is a simple replacement. The hardest part was that I had to shorten the seal because it comes 15 to 17 inches. So it needed to be shortened to properly fit. I cut the seal to fit, then took the metal hook on the end and super glued it to the cut end. I put a weight on it to make sure
Was this instruction helpful to you?
Thank you for voting!