CE30M5WKAA Gibson Range - Instructions

I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.

Removed heating elements and replaced drip pans. And by the way, this is the only 'pans' I could find to fit. Thanks.

simple ratchet extension and socket to remove screws and replace. be sure to crimp the connectors with pliers before ataching the element.

Removed back access panel of oven (several screws). Unplugged element wires (two slip connectors). Removed two element mounting screws from the inside of oven, and removed old element. Reversed proceedure to install new part.

I couldn't explain how to do the job any better than your instructional video does. As long as you follow the video instructions you should have no problems.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Simple Just plugged it in !

I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.

took out the two screws pulled the element out unplugged the wires, plugged in the new element, stuck the element back in the holes and put the screws back in

Probably a good idea to either unplug unit or make sure oven is in off position first, then remove screw on either side of old bake element, then gently pull out about 3 inches to expose wire connections and carefully disconnect each slide-on connector. Dispose old element in trash and replace with new one from partselect.com in reverse order. Very simple and much less expensive than either buying a new appliance(if you've been satisfied with what you have), paying a repairperson to come in and/or trying to hunt down the right part from a "local" appliance store/warehouse. The part was easily identifiable via the graphic depiction on the partselect.com website, arrived in excellent condition and in record time for normal ground shipping(less than 2 days from order date!), and I experienced kind and competent customer service from the get-go. A do-it-yourselfer like me really can't ask much more than that when it comes to appliance repair!

I pulled the range out of its space, disconnected the power cord, disconnected the two electic power wire on the heating element. Then I disconnected the two retaining nuts on the inside of the oven and pulled the heating element out. Then reversed the order and wala, hot oven and now my corn bread does not burn.

Open the oven door and removed a metal screw from each side of the element on the rear wall of the oven. Pull each side of the element out about 2-3 inches and you should see the terminal fitting with a spade type connector. Remove the connector from each side and discard the old element. Place the connectors on your new element and push it through the openings that the old element came out of. Replace each of the metal screws and you are done.

I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.

Only two screws to remove, so it was very easy to just pull the element out, remove the wire connectors from the old element and place on the new one. This is one repair you should NEVER call a service person for! Be brave--anyone can do this.

Actually, a child of average intelligence can do this. Just pull the surface elements, take the old drip bowls, install the new ones and re-install the surface elements, including the brand new one I received.