GGF354BHWA Gibson Range - Instructions

i had to remove all the broken glass then removed the metal that was holding the glass. set the new glass in the metal strips and screwed it back togethr. i also had to remove the frame from the door in order to get to the inside glass. then i had to put the door back together.

First, I want to say how WONDERFUL your service was. I needed more info on a part and your phone rep. e-mailed me a picture of the part from which I was able to be sure it was the right part. I ordered the pard one day and they were delivered to my door the NEXT DAY....talk about service!!!

My husband did all the replacing, he had no problems with any of the 3 items he replaced, he said they were all easy to replace. They all work great. Thank You!!

removed two screws disconnected inlet pipe and two outlet pipes, removed regulator. Replaced with new regulator. performed leak Test.

The repair was fairly easy. The oven door was attached to a spring arm that had one screw holding each arm to the door. Once off, the outside set of screws were removed and saved in a small dish. Each section had 6-10 screws, to it's best to keep each set separate from each other. Each of the three layers (of the door) came apart easily by removing the screws for each section. The inside (broken glass) lifted out, was replaced, and the sequence was repeated in reverse. During the reassembly I was able to clean the other layers of glass that had gotten build-up on them over the years. Total time start to finish was about 30 minutes. Only tool required was a screw driver! Probably saved 100+ dollars!

Our original oven ignitor went bad. The gas supply won't even open, unless the oven senses the proper voltage / resistance across the ignitor, so that gas won't be flowing without ignition.

PartSelect was very good about providing me with the proper part, after I got the part number from their schematics and wiring diagrams, on the website. The first replacement part actually arrived, broken, from shipping, but when I called them, they immediately reprocessed the order, and sent me a new ignitor, to arrive the following day. I was very satisfied with their professionalism, as I've been in the past with them, as well.

On to the actual repair:

I removed the broiler drawer from the drawer slides, reached under the main oven chamber, unscrewed the two screws holding the ignitor in place, and cut / disconnected the two wires supplying the power to it.

I then put the new ignitor in place and screwed it back to the mount, used the wire nuts that came with the new ignitor to reconnect / splice the wires, and put the broiler drawer back in place.

Oven fired right up!

Entire process took less than 35 minutes. (Likely would've taken a bit longer, but this is the second replacement for the ignitor, since we've owned this oven, so I already had a good idea how to do it. (The first replacement for this particular part was NOT from PartSelect, so we're hopeful this one lasts a while longer than the previous one.)

Thanks, PartSelect!

thanks to you 'r assistsnce First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, and changing the regulator was just as easy.

no need to remover burner. Lift top up use a 1x4x5" to hold top up. Use short #2 screw driver remove screw and replace with new igniter

Slide out the old; slide in the new!

I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!

I searched the item I needed and followed a link to PartSelect.com. I paid a little extra for shipping and literally recieved the part in two days. The part was an absolute perfect fit and my wife and myself have never been happier. Home cooked meals again thanks to the folks at PartSelect.com. It couldn't have been an easier.

1) Turn off the gas and disconnect the power

2) Remove oven door. There requires that you remove the two square drive (SD) bolts on the inside, partially close the door and lift it off the hinges.

3) Remove the grills.

4) At the back remove the rear shield (aluminum panel held by 2 SD sheet metal screws.

5) this exposes the broiler igniter and its two wires. If its been replaced in past, there should be two porcelain screw-on wire connectors. Undo the connectors by turning them counter-clockwise. With a volt-ohmmeter, measure the resistance across the igniter. If its open circuited, its broken. If not, then its in the circuit board, and this help stop here. If this is the original igniter, it ends in a plastic connector. Disconnect by pulling it apart from its mating plug and again, check the continuity of the igniter. If its defective, reconnect the connector and cut each wire on the igniter side. Strip back about 1/2 inch of insulation on each lead.

6) inside the oven, using the SD driver, remove the 4 screw securing the broiler burner from the roof of the oven. The burner can now be removed, pulling the burner away from the gas jet on the right.

7) The igniter is now exposed and can be remove by removing the two SD drive screws.

8) Replace with the new igniter, being careful not to touch the black element, and feeding the wires though the rear oven wall.

9)Reverse the above dissembly procedure.

10) Broil the sausages.

Make sure you unplug the oven before you begin. I removed the old igniter. The top wire on the igniter goes to the back of the oven and plugs into a flat blade type connector. Instead of using the twist wire nut I used a flat connector because it was easier to put on and is foolproof. Make sure you cut the plastic insulation off the connector so it does not melt when the oven is in use. I used a wire nut on the other wire and that was it. Very simple and the oven works great again.

It was great. We ordered the part, it was shipped the next day and I had it the day after that. It was easy to install and the stove has worked perfect since. Color us happy!

New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.

Removed screws. Unplugged temp sensor. Put screws back in. So easy a caveman could do it.