KEC3M6NSAA Gibson Range - Instructions

We tested all of the other "functions" of the oven to make sure that everything else worked fine, and we realized that the problem really had to be the element.

We ordered it and it came within 72 hours! We simply unscrewed the faulty element, made sure that the wires were handled carefully (circuit turned off!), and inserted the new element and rewired and screwed back into place the screws that were removed.

Simple as pie! You can do this! You don't need a service call for this one guys! Get BRAVE!!

It was really easy. Removed the racks, removed the 2 quarter-inch screws with a nutdriver. Pulled the bad element out about 3-4 inches, enough to unhook the wires attached to the element with spade connectors. Unhooked the wires and removed bad element. Hooked up new element and reversed the process. Thanks PartSelect!

Removed 2 rear screws. Pulled out element. Popped out 2 wire clips. Replaced old element with the new one and attached wire clips. A caveman could do it.

Read the reviews and followed the same procedure. Very east..took about 10-15 minutes.
Product shipped same day/next day it was delivered and it was installed less than 30 hours after it was ordered.
Exceptional service.

My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!

Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.

juist loosened nut and pulled element out about three inches, detached leads, reattached new leads and installed.

Very easy repair. First and very important step...shut off power to the oven! Then removed two small screws holding element to back of oven, gently pulled it and the wires connected to it toward me, disconnected the wires, connected the new element and reversed the process. However what I really appreciated about this was how easy it was to find the part on PartSelect.com. It was difficult to read the model number stamped on the plate at the front of the oven, and I got 1 letter and 1 digit wrong. But when I did the search, instead of just telling me "not found," it offered a list of model numbers that were close to what I'd entered, and the first one was correct. Very helpful! The online store is very well set up and easy to navigate.

Just took the back of the stove off and removed old one and put new one in. Very simple.

took out the screws at the back of the oven, removed the old element and put the new one in, replaced the screws. The new part was mostly the same size as the old one, some of the angles were different and the ends slightly different, but it fit and works great.

First, I removed the two screws that hold the element in place. I pulled out the element about 2 inches, and then I wasn't sure what to do, so I called my son and he finished the project in about 5 minutes or less. He pulled off the wires and then put the new element in place, slipped the wires on the new element, then pushed it back into the holes and screwed the screws back in. Worked great.

i removed the stove eye and the old drip pan. then i placed the new drip pan in and replaced the eye. the new drip pans fit way better than the ones that i took off of it.

Unplugged the appliance then removed the two screws holding the element in place. Pulled it out about 2-3 inches then pulled the wires off. The replacement element has 90 degree connectors as opposed to the original 180 degree connectors but that didn't affect installation and hasn't affected operation. Slide the wires on the new element, slide the element back in the oven, screw it back in and you're good to go. Trust me, easiest repair to do.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.