CEC1M2WSAB Gibson Range - Instructions

The element pulls out easily and slides right back in and the drip bowls just lift in and out. TaDa !!

I did as instructed on your video of how to install the terminal block, btw GREAT VIDEO!!
I'm a 66 year old female and if I can do it, anyone can.

Thanks, PartSelect

Try to buy new unit from local dealer, was told unit was too old. Went on line to Part Select and found part needed and ordered part. When part came, I removed two screws from in oven and four screws from back of range, discorrected two wire leads from bake unit, removed old unit and installed new unit, connected wires, reinstalled back cover, and installed bake unit to oven with two remaining screws. Job done, oven is now working. The part costs with shipping was around $33.00, new oven $600.00. Thanks Part Select.

First shut power to oven off, removed the oven door and oven racks. Removed the 2 screws from the back of the oven holding the element in place. Slowley pulled the element out and removed the wires, pulled off with my fingers. Replaced the old with the new in the reverse order. Saving the Wife a pile of money.

Thank You,
Jerry R

first i remove the two screws that hold the element then i pulled the element out few inches out i disconect the two wires and i put the new element back in place 10 or 15 minutes top.really easy

Shut off the power at breaker to range,removed the screws and pulled out the element a few inches to disconnect the wires .Connected wires to new element., screwed it back into oven wall.It's a snap!

Repair was simple. Unplugged stove, removed a plate from back of stove. Disconnected wiring. Removed screws from inside oven, removed old element, installed new element. Replaced screws, hooked up wiring, replaced back plate, plugged it in, used it that night.
Thanks for sending the right part the first time and getting it shipped so quickly.

I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.

Turned off power to oven at breaker box.
Removed one screw that holds the element in place. The other screw would not unscrew, I went to hardware store for drill bit and special hand tool (which cost less than $15) to remove stuck screw. I didn't have the right size screw, so I went back to hardware store for two new screws. Pulled the element out and disconnected the two wires(they are plug-in). Lost one wire into the back of oven because I did not hod it for the new element to plug onto. I removed the back of oven by unscrewing several screws and located the wayward wire. I threaded it back into the hole (easy) and someone grabbed it and held onto it while I screwed the back of the oven back on. Then I placed the wire connectors onto the new element being sure to squeeze hard with pliers so there would not be any slipping off of the wires. The power was restored and the element worked great. A less than 30 minute job took over 2 hours because of inot thaving he right tools.

Unscrewed back of oven the plate that was holding on old element, removed it (plugged into small wire device)
Plugged in new one and replaced screws to hold in place.

I just had to plug the new burner plate in the receptical
and it works again very well.

Removed the 2 element holding screws, disconnected the element leads & remover element. Replaced with new element.
All in all a real easy job (wish all repairs went this easy)
PartSelect had the element at the house within a couple days (Correct part I might add) which made the wife happy !!

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

Took the back panel off. Removed the 2 screws from the old element,removed it. Put the new one in and replaced the screws. Put the back panel on done. What took the longest was cleaning behind there !!

The meltdown was a spectacular event. After clearing the kitchen of smoke and allowing the oven to cool down. I easily removed the remnents of the old element by removing the screws holding each side in place and disconnected the two wires. I then insulated the hot side wire (red) to prevent the possibility of a short when resetting the breaker in order to use the stove top. The next day I found PartSelect.com and ordered the very reasonably priced new part with optional overnight shipping. it arrived at 1:00 pm the following day. Installation was a simple reverse of the removal. The oven works great and I now keep a fire extinguisher in my kitchen.