CEC4M6WXD Gibson Range - Instructions

i called Sears and ordered the element and they charged me 16.99 plus the part to ship the next day. after 1 week i called them and they said the part was on backorder. i then check with them each week almost a month and the part was still on back order, I asked if they could fix it faster if they came to the house, they informed me it would cost 65.00 for a repair person to see what part i needed and after that they would schedule m e for a repair when the part came in. meanwhile i could not use my oven. i happened to go on line and came up with your web site. i ordered the part and 2 days later my son installed it. my oven works great . your company is awsome.

Repair was so easy, Just remove the two screws one on each end of element slowly pull element towards you till you see the ends. Carefully
unplug the wires and then reinstall the new one and put screwes back in and you are all done

unfastened clip at back of oven w/screwdriver. Pulled out the plug, unplugged the element. Plugged in new element, pushed back into place, refastened clip to hold it in place at back of oven.. Done

1.Take no chances. Turn off power at main breaker box (Range). 2 2. 2. 2.Remove inside grills then pull damaged element forward to expose wires and screws. 3. Use nut driver or phillips screwdriver to undo both screws. 4. Remove burnt out element then replace it new one. Make sure both sides are firmly pushed onto the wire terminals before tightening screws. Replace grills. close oven door then turn breaker at breaker box on again.

Turn off the power to the range. Remove oven racks. Remove the two screws and slowly pull the element out being careful not to pull the wires off. Remove the two wires then attach them to the new element. Push the element back in place, put the screws back in, turn on the power and turn on oven to make sure the problem is fixed

slid the old one out and slid the new one in.turned the unit on and it works

Read the instructions provided and simply installed the guides. Total time was less than 5 min.

Unplugged stove, removed screws holding element In place. Pulled element forward exposing electrical ends. Removed connectors, re- connected ends to new element. Pushed element back into holes and reconnected the screws. Plug stove back in.

Loosen 2 screw with a 1/4 nut driver. Pulled element out to expose connections. Carefully disconnected old element and replaced with new element. Pushed wires back into holes and replaced the screws. (Note: Be careful not to let the disconnected wires slip back through the holes. This almost happen to me)

For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!

Took out 2 screws unclipped the part put the new one on and i was done. Very easy fix .. Baked a cake right after to celebrate

The new part was shipped and recieved very fast.
I removed the old one and installed the new one going by how I took the old one out. It was simple to do even for a 75 year old lady.. Thanks.

First I gave my roommate (an engineer) a screwdriver to remove the two screws that held the element in place. Then before I could hit the switch for the circuit breaker, he nearly fried himself by trying to take out the element! He gave up helping me after that.

Then I turned off the circuit, pulled the oven out and unplugged it, removed the racks from the oven, removed the two screws that hold in the element, and lifted up each side of the element and pulled each piece out. Unfortunately, they were a little stuck in back.

So I pulled out the oven, unscrewed the 6 or 8 screws that held up the back panel, and pulled the back panel off. I disconnected the two wires clipped to the element and pulled the old element out by lifting up and pulling them out. I then put in the new bake element, clipped the wires back on, put the oven's back panel on and screwed it in place, and then screwed the bake element back in with those two screws. Easy - a

Had to remove the old element and had problems with the element shorted on the quick disconnect. After having my son unplug the appliance and cutting the quick connect off. My son then installed a new quick disconnect and the bake element.

We called a local repair shop and they told us that it would take a month to get our part and it would cost over $50 for it. We went online and found PartSelect.com. The part was here in less than one week and it cost less than $40. My husband pulled the stove out from the wall took a screwdriver and unscrewed the screws, slipped in the new part and screwed the new screws in. It took him 15 minutes to fix it and now my stove works better than it has in many years!