Models > CEC4S6WSAA > Instructions

CEC4S6WSAA Gibson Range - Instructions

Jump to:

All Instructions for the CEC4S6WSAA
61 - 75 of 239
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Doris from SUN CITY, AZ
Parts Used:
316048414, 316048413
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Drip bowls needed replacing
Removed the old ones and inserted the new ones.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from LANOKA HARBOR, NJ
Parts Used:
318372210
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carolyn from OCEAN PARK, WA
Parts Used:
316048414, 316048413
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Rusted Drip Bowls
This range is probably 30+ years old. Still works great. Just needed to replace the Drip Bowls.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from UNION, OR
Parts Used:
5303935058
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
replaced terminal block for element
followed the video provided on line which was very helpful..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Chuck from EVANSVILLE, IN
Parts Used:
5303935058
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from PRAIRIEVILLE, LA
Parts Used:
5303935058
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Helen from PAWLEYS ISL, SC
Parts Used:
316048414, 316048413
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dr. Johanna V. from North Conway, NH
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Wrench set
Oven element burned out
Really easy--unscrew screws, pull element out, unclip wire connection. Re-clip to new burner, put back in--done. Saved a $100 tech trip PLUS double mark up on part!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kyle from Jacksonville, FL
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
The old element caught fire.
Unscrew the old one and unplug the wire leads. Then plug in the new one and bolt back up.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Simon from New Port Richey, FL
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
oven heating element
I just removed two screws. Pulled the element out, unhooked the wires. plugged the wires into the new element screwed it in and was done
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Elizabethville, PA
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Lower element wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, replaced witht he new element
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Wyndmoor, PA
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven bake element would'n heat
Removed the racks first. Then removed the two screws that held the element in place.
I then pulled the element out about three inches
exposing the connecting wires.Each wire has a female slide type connector just disconect each one and then connected the new element .
Attach new element by reptacing the two screws.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Columbus, IN
Parts Used:
5303051519
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven heating elelment stopped working
I watched my husband do this repair so if it happens again I can do it myself. He removed the screws holding the element in place, unplugged the element, plugged the new element in and replaced the screws. I am so glad I found your site. The posted pictures and measurements made finding the exact part a breeze and the element arrived in a couple of days. We saved a bundle!! Thanks.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
PETER from BROOKFIELD, WI
Parts Used:
5303051519
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
element burned out
pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Garrettsville, OH
Parts Used:
5303051519
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bake element split and quit heating
If I didn't need my oven ASAP, I would not even have attempted to do this repair before my husband came home. But he wasn't going to be home for hours, and I needed it now!
First, I took off the back panel. Slid off the wire connectors. Then moved to the inside of the oven and unscrewed the two screws that secure the element to the oven, and pulled the old one out. Put the new one in and reconnected the wires from the back, and replaced the back panel.
That was it! It worked great!! Very simple.
I called my husband immediately to tell him of my great accomplishment!! I was so proud of myself!

Thanks,
Vicki
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CEC4S6WSAA
61 - 75 of 239