CGC4M5WSTE Gibson Range - Instructions

First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom cover, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.

had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you

Removed the storage drawer to access the door springs.Removed the worn hinges and installed the new hinges,connected the springs. Removed the oven door before anything else was done.The could not have been any simpler .

Remove drawer, remove oven door, remove hinge and pieces. Get the spring loose. Attache new hinge to frame, reconnect spring. Slide door back on hinges.

Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.

Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. Stripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.

replaced it

I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connected them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.

Replaced same very simple.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.

It was a snap!