CGC4S7WSTB Gibson Range - Instructions

I unplugged the stove then pulled the disconnected the wires that controled the igniter. I took the two screws off that held the igniter to the pilot port. I hand to cut the wires on the new igniter to some-what match the lenght of the broken igniter. Then I cut the connectors from the old part and used the fire resistant wire nutes that where included with the new igniter and connected it all. Put all the screws in tight, double checked every thing. Finally I plugged it in and it was working.

Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working over the oven door,but I am old. Good luck

After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!

followed directions enclosed.required removal of oven door and old igniter

open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!

Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.

Install new igniter. You will need to cut existing wires from old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.

took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite

remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.

pulled drawer out and took old igniter off and replaced it

This was very easy. Just remove the bottom of the oven by removing the two screw in the back. Then remove the baffle from under that and you of will see the ingniter. The one wire will reach the gas valve, just splce the other. 6 screws is all it takes. Turned it on worked perfectly.

My existing igniter glowed but the oven still did not light. I determined it was too weak to activate the gas valve so I replaced it. Simple fix, four screws, wire nutted the two leads. Fired right up, took about 30 minutes to replace.

1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.

Opened the oven door, removed the racks. Removed the bottom cover, two thumb screws in the rear, bottom, of the oven. This exposed the top plate of the burner, (actually in the top of the broiler section) 1 nut took this cover off. Now, the burner and the igniter are exposed. Two screws removed the igniter, and two wires with ceramic wire nuts. Disconnected these two wires and that was it. Installed the new igniter in reverse procedure as above. Pretty easy. Probably should have turned off the power to the Range first just to be safe.

Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?