CEC2M4WXD Gibson Range - Instructions

The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.

Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )

I unplugged the stove from the power plug in the wall. There are two screws at the back of the oven to hold the element in place. I removed the two screws. There are wire clamp inserts that attach to the element. Once the element was loose from the back wall of the oven, I gently pulled out the wire clamps. Removed the element. I laid the new element in the bottom of the oven and gently pushed the wire clamps into the new element. Re-attached the screws and put the power back into the wall and I was done. Easy, easy, easy. As for the drip pans, I pulled the element from the plug just under the stove top, cleaned the element and replaced the old drip pans with the new. Slid the element back into the plug and I was done.

Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.

Used a slot screwdriver to pry the old guide...clipped the new guide into its place.

ordered new heating element, arrived promptly as expected, compared new heating element to old one and it matched in size only diameter a little different, removed two sheet metal screws holding element in place and pulled out element to expose conductors and removed them with screwdriver. Installed conductors on new heating element slid into holes and installed screws, turned power back on(first step is to turn off power) turned on oven to preheat and she worked like a new one. Thank you PartSelect. Saved me a bundle,

Open the door and slide in the new rack.

Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY

Just followed the same instructions that the other people did when replacing this element. Was very easy to replace . Just turned off the power , rwemoved the two nuts , pulled the wires out about 3 inches and unpluged old one and pluged in the new one, replaced the nuts and volia ,DONE

Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..

Turn power off. At oven, removed two screws from element hanger. Pulled old element out exposing spade connectors. Pulled connectors lnstalled connectors on new element and shoved back in stove and replaced screws. Work done with oven door open using drop light. Check for debris, turn power on, turn oven on to check.

first I emptied the contents of the drawer,then pulled drawer open to it's fullest, then lifted drawer so as to tilt slightly, then removed drawer by continuing to pull straight out. then I removed the glide from its protective packaging and inserted it in the same spot as the broken glide was at one time

first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks,
Fred . it was so reasonable i got a spare.

using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine