CGC3S5DXE Gibson Range - Instructions

I removed the bottom of the oven and flame guard for access to the ingniter. I then replaced the ingniter. The oven works like new now.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

replaced it

I cut the wires from the old igniter near where it said to. I then connected the new wires to the old ones, put it back on, the way I remembered it being assembled, but still won't heat up. I tried to get an enlarged detail of where I was working on, but I couldn't enlarge it from your website. My friend, who knows about electricity, worked on it for several hours last pm(He's an electrician), but could not figure it out with the scamatic that was on the range, because he was not there when I disassembled it,

The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.

1st took out switch from thermostat unit, located right on the other side of where the temperature knob is located (that controls cooking temp of the oven). Had to lift up range cover to get to the thermostat. Tested this switch with a meter and found it was OK. This made me suspect the igniter, so I ordered one.
To install I first unplugged oven (to prevent getting shocked) then took off the drawer on the bottom compartment (push in on tabs on rails until they release). Then take out two screws holding igniter. Mark wires with tape so you know which one goes to the upper part of the igniter and which one goes to the lower part. Then cut wires as close to the body of the igniter as you can so that you have plenty of wire to work with. Then hold igniter in about the place it will be mounted and mark the wires on the new igniter where you want to cut them. Leave a little extra so you have wire at a length that is easier to work with. Scrape off 3/8 inch of insulation off the end of each wire and connect the wires with wire nuts. Re-mount igniter. Put drawer back in. Plug oven back in and try the oven. I hope it works. Mine did thanks to God. Take care.

Unplug appliance. Remove the bottom of the oven (2 screws in back of oven bottom), remove burner cover (2 screws in front and nut in center holding burner). Pull out the bottom storage drawer under the oven and unplug both wires from oven Igniter which are located in the back. One wire plugs into the gas valve and the second wire went into a connector that was on the lower left. I removed the screw on the back oven wall that held the burner so I could remove the burner for ease of work. Remove two screws holding the old igniter. The two screws holding the igniter to the side of the burner were stripped and they took a little time to remove but I replaced them with two new screws I had in my misc. screw drawer and had no issue. Cut the top wire and splice it onto the top wire of the new igniter using the porcelain wire nuts provided. Do the same with the bottom wire. Re-assemble and plug back in. Everything worked perfectly.

I exposed the ignitor through the inside of the oven and then removed the two screws that held it in place. I then cut the wires underneath the stove ans reconnected them to the new part with the wire nuts provided. It was a simple repair.

Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.

After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!

removed bottom plate in oven removed three screws and cut two wires.

This was a very easy project.
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repaired our stove myself!

Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked great.

Removed lower burner covers and fan cover to access igniter. Unscrewed igniter and pulled out as far as possible. Marked both wires and snipped them. Twisted on wires from new igniter and mounted igniter. Pulled excess wire thru to back of oven and reassembled covers from first step. Last step was to explain to wife that she needs clean in there MUCH better.

followed online instructions