RU384C3 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
old worn out drip pans
All I had to do was remove old drip pans and insert the new ones. What a huge difference it made. It made my stove look so much newer.
Was this instruction helpful to you?
Thank you for voting!
I replaced these parts to brighten up my stove before selling my home.
I lifted the coils, removed the old bibs and replaced them with the new bibs.
Was this instruction helpful to you?
Thank you for voting!
missing parts
Pulled the elements out and replaced the parts that were missing . Then replaced the elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLARD from GLOVERSVILLE, NY
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
instructions could be better
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Hamilton, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Shaft for burner control knob broke off
I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mirtes from Marlborough, MA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element not heating
Removed the terminal block. Cut the wires. Cut the sheathing to expose the wire. Connected the new wires with the old wires by twisting them together. Added the wire nut and reconnected the block. Tested ok.
Was this instruction helpful to you?
Thank you for voting!
Dirty and stained Pans and ring
Just pulled out the three burners and lifted the pans. Lifted out the ring. Pivoted up the 3-way burner, and lifted up the pan with wider slit. Put new ones in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Austin from Blackfoot, ID
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Poor connection to element
In a little over 15 minutes, I was able to pull the element and pan, snip the wires on the terminal block and use the wire nuts to fasten the new terminal block. The shrink wrap tubing went into place easily and all went back together easily. Best of all, the two year problem of a poor element connection was solved in a matter of minutes for a few dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from YarmouthPort, MA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burned out terminal block
Hi, Very simple fix.Take out 1 screw & clip wire with snips. Put wires from new unit together & screw on wire nuts. Put shrink tubes on & heat with liter till it shrinks to what you want. A $15.00 fix is better than a $500.00 stove. FIRST STEP TURN OFF THE BREAKER & YOU ARE GOOD TO GO!!!!! Ron
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Anchorage, AK
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Several burners quit working
Had one burner that was completely out as the old terminal block had a broken contact. The other burner was intermittent and would arc when heating up. There are several slightly different size terminal blocks. I had a hard time re-inserting one of the old burners into the new terminal block but got it to seat. I put a new burner with the new block on the other one and it fit much better. Additional tools used were a wire stripper and a heat gun for the heat shrink. The stove works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Nashville, AR
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
R had ight front control made loud noise when contacts opened.
This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.
Was this instruction helpful to you?
Thank you for voting!