JKP78G4K1 General Electric Range - Instructions

remove/replace baking element. Relatively simple to do; however, I used the old screws/nuts as they worked better than the new ones which were included.

I shut down the electric to the oven at the circuit breaker. Then i loosened the mounting screws and pulled the element from the back wall of oven. Then i disconnected the two leads to the element with a phillips screwdriver and removed element. Installation was done in reverse order.

Easy repair. The toughest part was disconnecting the wiring from the old element. Once that was disconnected it went very well.

Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.

Took out old element with screw driver and replaced new element with screw driver, very simple.
We were so happy with the customer service, had the new element the very next morning. Thank you.

Cut the power off to the oven. Removed both of the racks in the oven. Removed the 2 screws that hold each element in place. Pulled the bake element out as far as it would go and unscrewed the two wires. Then did the same for the broil element. It has a guard to keep it from dropping down and I had to remove that. The broil element is a little more difficult to remove but i had read that in the previous users writeups. Overall it was a great experience from a price, delivery and installation process.

The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened with the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!

Turned off power. Unscrewed two screws and pulled old element out of oven. Disconnected the two wires. Cleaned oven thoroughly, held new bake element with soft rag so as to not get fingerprints all over it. Wired new element and screwed it back into oven.

Baking sweet potatoes as I write, they will be delicious with my black-eyed peas and ham, a New Year's tradition in my neck of the woods.

First turned off the power to the oven then removed two screws holding element in place. Pulled it out a couple inches disconnected the two wires. Then connected two wires to the new element pushed it back into two place and reinstalled screws that hold element in place. Really easy about 15-20 minutes to complete

several months ago the bake element in my oven started cracking. When it started sparking I knew I had to replace it or get a new oven. I ordered the part and it was easy. The old one fell apart as I removed it. I honestly don't know how it was still heating. Anyway, all I did was turn off the electric to the oven, then I had to remove to screws that attached it to the wall of the oven. That was the hardest part because I couldn't see them well so I had to put a lantern in the oven. Then I had to pull it out enough to remove the screws from within. Then I just reversed the process to install and everything worked great! Saved me a lot on calling a repair man.

Part was a breeze to install. I turned the power off to the oven at the breaker. I then unscrewed the bolts holding the old element in and disconnected the wires. I attached the wires to the new element and bolted it back onto the oven. I turned the breaker back on an tested the new bake element. Worked great! Now it heats up like it should. The whole process was very easy.

The part was ordered on a Friday afternoon. It arrived the next morning! Threw the breaker, removed the racks, removed the old element and put in the new one. Done.

Turned breaker off to oven. Removed 2 screws from burned out element in back of oven and pulled it out. Installed new element and tightened the two screws. Very easy.

My oven is 31 years old so was suprised I could still get parts.

Bottom bake element is fastened to back wall by 2 screws remove those first.
Slowly pull out old bake element notice 2 wires are fasten to old bake element by 2 philips head screws. Remove screws from wires fastened to old bake element
Discard old bake element.

Reverse the order for assembly.
Replacement part is the exact fit and entire replacement took 15 minutes.

EASY REPLACEMENT

Unscrewed the two screws holding the element to the back oven wall, then I was able to pull the element out. I then unsrewed the two screws holding the two wires to the element. Installation was the reverse. Pretty simple job.