J335*02 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Vineyard Haven, MA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat.
First I turned the circuit breaker off, then I removed the two screws with a nut driver, that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires with a straight scewdriver.
Reversed the the above process to install new element.
Oven was 27 years old.
Repaired and operational in less than 15 min.
Reversed the the above process to install new element.
Oven was 27 years old.
Repaired and operational in less than 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAMELA from RIVERVIEW, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven baking element would not heat
First , for safety, I flipped breakers to kitchen applicances to cut off the power. Removed the 2 screws that held the old element in place. Pulled it out a couple of inches and disconnected the 2 wires attached to the prongs of the element. Reattached them to the new element, pushed it back in and replaced the screws. Turn power back on and voila! ... was ready to bake again! All this is a matter of 15 mins!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from Waterford, CT
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, put the new one in and reversed the procedure. Also delivery was great, I ordered the part and received it the next morning. I highly recommend your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Marysville, WA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
The bake element broke in half and did not heat after that
First I took out the oven racks removed two screws then I pulled it out a couple of inches to expose the wires and removed the screw. Put the new element in place and replaced the two screws put the wires back and replaced the two screws that hold the element in place.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gainesville, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element cracked and arcing
First I unplugged the oven from the wall. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The installation process was just as easy as the removal. Approx 10 minutes and I was cooking. BTW, the heating element was at my house the next day after ordering. Great service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Tulsa, OK
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
top element in oven was broken ,not working
Removed 4 screws and removed the old element and replaced in the reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from WEST POINT, UT
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broil element had a "burn through", w/n turn on
less than 15 minutes R2 the part, ops ck'd good. 4ea 1/4" screw/nuts, they didn't fight me...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duryea from Westminster, CO
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burn't up element
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Installed the new element reversing the process above
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Canal Winchester, OH
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Element had burnt out
First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lancaster, SC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out.
Removed element and installed new element. Fit perfect, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lanny from KINGSLEY, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
my bake element sparked and shorted out
Unscrewed four screws, removed old element, replaced with new part, done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce W. from Portland, OR
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken heating element
I took the old element out, compared it to the pictures of the GE replacement elements, identified the correct one and ordered. It came I installed it in 15 minutes and it works just right. I was unable to determine the model number of my old oven so the pictures of replacement elements were invaluable. Thanks for making it so easy to avoid calling a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margaret from lantana, FL
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
both oven and broiler coils were burnt out
extremelyquick delivery on standard mail and so easy to install and really the lowest price. so happywith this company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Tioga, ND
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Broken Bottom Bake Element
Super easy, 1 2 3 steps and your done. Make sure to turn power off, remove two screws off of back plate. Remove two screws on wire connectors. Throw old element away and connect both wires to new element and screw back into place. Turn power back on and start cooking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney from Trenton, OH
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven stopped working
very easy--cut power supply 2 screws then 2 more on element quick and easy
Was this instruction helpful to you?
Thank you for voting!