J335*02 General Electric Range - Instructions

First removed screws then removed burned out element.Replaced with new element and replaced screws and cooked pizza.

Turn off the breaker. Unscrew the element. Remove and replace with new element. Screw it back into place. Turn on the breaker.

That simple, that easy.

First I removed the two screws that hold the element in place. I then pulled the element out about 2 inches and disconnected the two wires.

I reconnected the two wires to the new element and screwed the new element to the wall of the oven where the element was held in place.

The customer service at PartSelect.com is wonderful. They assisted me to located a part for a 40 year old oven. Took only a few minutes to take the old one out and put the new one in. Process was pretty self explanitory.

It was realatively simple, turned off the power to the oven, removed the bake element , by loosening the two metal screws in the back of the oven, with a nut driver and removing the screws, then pulling the element outward, to expose the two wires ,that were connected to the element, using a nut driver to remove the two screws and a pair of pliers to hold the wire connectors, then removed the old element. Installed the new bake element, by connecting the two wires to the element, with the two screws, then pushing the element back in place , attaching the element to the back of the oven, with the two metal screws, finished with the installation, turned power back to the oven , and tested to make sure the oven worked , all done.

Repair was easy.
Note: the element leads have a potential across them,
so unplug the unit or you'll have an arc strike.

I liked the selection method at PartsSelect.com.
Finding the replacement part was easy from the pictures.
The prices were reasonable.

The part came next day, which was a surprise.
Removal and Installation was 4 screws.
I have become a DIY hero.

Only downside was going out for dinner every night ended.
This site is now a Favorite.

Tried contacting GE and no luck, they did not have vintage parts. After searching and locating Partselect, I was able to see a pic of the actual replacement part. I wasn't sure about purchasing online (1st timer) but decided to go for it!

I was able to track the package, although FedEX was setup to deliver to my resdient, I had the package addressed to my office but we worked that out also and walla.

I was very please and now I can bake my famous Pot Roast again. The oven was not working for 8 mos.

Good Eaten!

SJ-Long Beach CA

Removed 2 mounting screws - Removed 2 screws used to attach wiring to element. Received new element and re-attached the 4 screws.

Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.

removed 2 nuts holding the element in the oven. removed 2 screws that secured the wires to the element. installed the new element in reverse.

The delivery of the part was within 3 days.I only had to connect the two screws had biscuits that night.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Turned power off to oven. Unscrewed back plate exposing wires connected to heating element. It was difficult to unscrew the connections between them as it was hard to reach in because the oven door was in the way, but i finally succeeded. Unscrewed the bracket holding the burned out element and then attached the wires to the new element. Attached the bracket and I turned on the power. I then tested the oven and it worked.

My husband did the repair in about 15 minutes. It was apparently self explanatory and required no directions. Take the old one out and replace it the same way it came out. And viola!!, the oven works like new - all for about $33. Thanks