RGB790SEHS General Electric Range - Instructions

I replaced the oven igniter, discovered the floor of the oven had rusted through, so I replaced that as well. The burner on top of the stove would not light as it was designed, and because the 12 screws that hold the range top and burners in place were rusted in place I ended up buying a new range because removing the screws on the burners proved impossible, even when I tried to drill them out with a lefthanded screw removal tool. I should have just kept lighting the burner that would not light, with a match. That was a repair too far, that forced me to buy a new GE Range and throw this one in the trash. The igniter, oven floor replacement was easy. The burner igniter after 18 years proved impossible. .I installed the 18 yr. old burner grates on the new range, but the drip pans would not fit the new stove. New GE Range instructions were near useless. Do Not trust them, especially the Orifice change details NG to LPG.

1) Verified it was the broiler igniter that was damaged.
2) Removed the oven door, the lower pot storage drawer and the top range panel.
3) Turned off the gas supply in the top range area. Pulled the electrical plug-in out of the lower electrical panel (behind the lower drawer).
4) Used the nut driver to remove the two (2) 1/4" screws that held the igniter to the back wall of the oven. I later read in the Use & Care Guide that this is easier to do if the broiler burner cover is removed first.
5) I pulled the damaged igniter away from the back wall, expecting to expose wire connectors or splicing but was only able to get about 6" of the two (2) insulated wires before I could not pull them any further.
6) Therefore, I cut the wires and, without a proper wire stripper, cut about 3/8" of insulation away in order to make a splice between the wiring from the new igniter and the wiring coming out of the back of the oven. Big mistake ..... do not recommend this without using a proper wire stripper! I must have cut into the existing exposed oven wiring on one of the wires such that when I used the twist-on to make the splice, most of the wires (those wound together to form one wire) were damaged and broke away. Unfortuantely I did not find this out until everything was put back together and we (my wife and I) did the test. No results!
7) I took everything apart again and when I tried to pull the wiring back out from in behind the oven wall, one wire came out with the twist-on in tact and the other came out "with no wire attachment".
8) I now had to figure out how to get into the back of the oven to retrieve the "lost connecting wire". It is quite simple when you know what you are doing but no instructions (that I had) advised that the upper back light gauge metal panels could be easily removed to expose the wiring. This was eventually determined and the connections were both made again in a more positive manner.
9) We (my wife and I) put it all back together and this time it was fine ..... just had to be patient while the gas purged the air out of the broiler burner line.
10) Lessons learned: GE made it easy "once you knew how it could be done". I suspect GE feels that service type people should be doing these things but with a 120VAC (vs higher voltage electric type ovens) system why not provide the info for the "do-it-yourselfers" as well?

The bolts were below the base of the oven, and very difficult to remove and replace. The directions were not applicable to our unit. The good news was the igniter was correct, even though we had to adapt the bracket.

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

I took all of the oven racks out , then the bottom cover, over the element. I immediately saw the igniter coil was broken. I took the element out and disconnected the two wires. (I saw that the igniter coil was broken and knew that must be my problem. I got my manual out and found the part number and got on line and started shopping. I found part select, the price was fair and ordered it the same day. It was shipped out to me the same day I ordered it. Received it the next day and had the oven working again. Easy to order, great customer service, fast shipping department. Great job to all of you folks at Part Select. I would recommend PS to anyone that wants to save money and do it yourself. Go for it. tk middlebury IN.

My repair was easy. The hardest part was trying to get the 2 small screws off and on the igniter. You need small hands or a small, angled socket set. I did mine with the door of my oven still on and maybe that was why I couldn't reach the screws that well. If you can do the repair with the door off, I would say that would be easier. As soon as the new piece was screwed in, it worked on the first try.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

1. I have searched info on the internet and found that site.
2. Initially I could not figure out how to unscrew ingniter. After reading more post I have found out how to access nuts underneath.
3. After I have removed lower drawer and unscrewed metal cover and then inginter nuts.
4. I have got a part with two wires attached to the igniter and two porcelan insulator, so it was very easy to cut old wires and connect with an igniter wires in parallel

/||\
||

First i removed the inside bottom of the oven where i could get to the actual glow plug igniter and removed the two screw that held the igniter in place. I than pulled the entire oven out allowing me to access the two wires connecting the igniter to the stove. I disconnected the wires and had to splice the wires as to be able to reach the appropriate connections. I reinstalled the igniter and upon testing the igniter worked properly. The entire process took me one hour.

Followed suggestions of previous posts. Removed oven door, warming drawer, pan in bottom of oven. Removed element to replace igniter. One thing I would add is I put a small piece of electical tape on the heads of the two 1/4 in. screws for the rear element bracket. This kept them from falling out of nutdriver.

Remove the broiler pan to get at the 2 nuts that hold the gas burner, remove them and then you can get at the 2 nuts on the back side of the igniter.

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore name on it.
I found out that even though the old ignitor glows well, it may not pull enough amps to open the gas valve.
First i disconnected the two wires on the gas safety valve that lead to the ignitor. These are accessed after taking the bottom drawer out. Then using a nut driver, i took out the two screws holding the bottom of the burner tube. Then inside the oven, i took out the racks and then the two screws in the back on the bottom. Then took out the bottom plate. I removed the one screw on the front of the burner tube, and removed the burner tube with the ignitor attached. I cut the wires off the old ignitor and attached them to the new ignitor with the supplied ceramic wire nuts. I attached the new ignitor to the burner tube and put everything back together. The bottom screws on the burner tube were very difficult for me to reach. Almost impossible to get both hands there to do the job.

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

After removing two layers of the oven floor I could not get at the igniter's wire connections. I found out that the new igniter was shipped with two wire nuts made of porcelain instead of plastic, so they were heat tolerant. Because of this, I was able to unscrew the original part and just cut the wires. I then installed the new igniter and spliced the wires of the new part to the cut wires that lead to the old part using the porcelain wire nuts and tucked the connections out of harms way. It worked fine.