1J2442M3 General Electric Range - Instructions

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!

Remove the old element by removing one screw and inserted new element and replaced the screw.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!

It was quite simple after the part arrived. I actually had forgotten what the connection was because one wire was yellow and one was red. After calling the number that I had to no avail. I went to the computer to ask how to install the part. Installed in little to no time. Feel like a Jill of all trades. Bring on the next problem.

Once I watched the video pertaining to the installation of the part, the job was very easy.

Element was in two pieces so it was obviously dead. I disconnected the stove from the power, I undid the two screws at the back of the oven and gently pulled the element out. There was enough slack to reach and pull the connectors apart. Done. I ordered the part from "PartSelect" and it arrived the next day. Unfortunately I ordered the element with "Screw" convectors as opposed to "push on" connectors. I bought a couple of connectors and cut off the original connectors from the wires in the oven and replaced them making absolutely sure they were well and truly tight. Two screws cam with the element from "PartsSelect (Thankfully). Connected the wires and screwed it back into place. Stood clear, plugged it in and turned it on to max. Worked just fine, Thanks

This is a forty five year old oven. It was only four screws and it was done. The new part works like a champ! This save me from buying a $800.00 replacement. I removed the two 1/4 screws holding the element to the back of the oven and then took the flat head screws loose from the terminals on the old element. I then put everything back as it came out; took less than 5 minutes and the part arrived overnight! Thank you again!!

first i removed two screws pulled that hold the element in then pulled element out about 3 inche disconnected the two wires now hot meals thanks

pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.

Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!

Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!

I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connecting the 3 wires, I reattached the element to the range.