JKP65G302 General Electric Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Took the element out and put the new element in place. Used the original screws - not the ones came with new element - to secure the new element back in place. DONE.

removed and replaced element as required.thank to your website i was able to order the right part.now i have your site marked as favorite.thanks for making this easy for the non professional.

Unscrewed face plate, unscrewed electric wires hooked to element. Cleaned out oven while I was in there...nice and clean now. Installed new element same way I took it out. Easy as 'pie'..which we'll be baking again now that the oven works.

The repair was a snap! Unscrew the two small bolts holding the back of the element in place. Pull out the element so that the connectors and wires are accessible. Unscrew the two wires from the element. Remove old element. Place new element in oven. Attach the two wires to the new element (two screws), place the new element in position and replace the two small bolts that were removed at the beginning. All done. Best thing? This is a 20 year old oven, GE didn't even have the part I needed. You did! Thanks.

IT was fast and easy! Thanks

Safety first! Flipped breaker for oven in main breaker box.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.

first remomed screws of element, then removed screws to + & - connections, removed element & replaced with new one. Was very easy to find new part thanks to your easy partselect.Thanks Alan Collins

removed 4 screws and exchanged units put the 4 screws back in. about 10 min.

Repair was easy! I asked my son to take out the old and put in the new! He did! The oven works like new again for less than $50.00!!! Thanks!

Turned off the breaker. Removed 2 screws and pulled the element from encasement. Removed 2 screws holding the wires to the element.
Reversed the process to install the new coil.
Done in 10 minutes

Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!

I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.

I pulled it out a bit and exposed where the element screws into the power.

To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.

After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.

Reset the breaker, and you're good to go.

Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.

so easy it doesn't need an explanation. Just remember to throw the breaker switch before beginning!

1) Turned off breaker and verified that the oven would not turn on. 2)Removed racks from the oven. 3) used nut driver to remove two mounting screws 4) used screwdriver to disconnect bake element from the wires. 5) used supplied screws to attach wires to new bake element. 6) pushed bake element into place and used nut driver to secure it in place with screws. 7) replaced racks 8) turned on breaker 9) tested by turning on oven with oven thermometer in place.

Flipped breaker to cut power to the oven.Loosened existing element using nutdriver to remove two screws in rear plate that attaches element to the rear wall of the oven.Pulled old element gently outward exposing two screws that attach element to existing wires.Removed those two screws with nutdriver to remove old element.Reversed the process. Turned power back on and turned on oven. Element worked perfectly.