J307*03 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tracy from Paris, IL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
elemant had burnt into
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then i connect the new element and and replaced the screwes that held it in very simple and I must say Part select was very fast at getting me the correct part the first time , they have earned a spot in my Favorite list
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Stuart, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Heating Element Was No Longer Working.
Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.
I put new element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
I put new element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Southampton, NJ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
No heat from bake element
Ordered part, took old bake element out, installed new bake element. It was real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from cape coral, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
lower element did not heat
First shut off power to the store and used a socket set to remove 2 screws and disconnnect the element. Connected the new element but had to use the old screws as the new ones did not work with my appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Ashland, MO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element burned out
removed the two screws, unsnapped the burnedout element and snapped new element in place, replaced two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Mount Airy, MD
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Element died
The hardest part was working in the oven.
Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals with vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.
Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.
Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.
Turn off power
Open Oven Door, remove racks
Remove two mounting screws with nut driver.
Slide the element out to expose the wire connections.
Remove the screws and pull the element out.
Place the new element in oven.
Clamp on to each of the terminals with vice grips to keep from bending the element and install the screws.
Slide the element back into place and put the two mounting screws back in.
Put the racks back in and turn on the power and test. You may get a little smoke off the new coil.
Like I said the hardest part is leaning into the oven to attach the screws, do not sit on the oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from WINCHESTER, KY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element had a crack in it and was shooting sparks from it
Unplugged range. Removed old element from back of oven which was held in by two screws. Unscrewed the wires that were attached to old element and screwed them into the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachelle from Oakdale, CA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven Element wouldn't heat
My 17 year old son and I (his mom) replaced the oven element in less than 15 minutes!!! It was so easy. We first unplugged the stove since I didn't want to go and shut off the circuit breaker in the dark!! We then removed the two screws that hold the element in place and started to pulled out the element. It was actually corroding in my hands as I pulled it out. We disconnected the wires and then put in the new element by reconnecting the wires, pushing the connections back in and replacing the two screws that hold the element in. The oven heated right up!!! What a savings to do it yourself and not have a repairman charge us extra to do a 10 minute job!! Thank you Part Select for your fast service. I will definitely look here before I shop anywhere else. Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Lincoln Park, NJ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
oven would not get hot when on the BAKE setting
Four screws and two wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Spring Grove, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bad Bake Element
The bake element in my 17 year old GE free standing electric range became defective. This element has 2 terminals -- black (240V) and white (neutral). While removing the element from the range, a 2nd black wire was pulled out of the back of the oven. This wire had a bare terminal connection and apparently had been loose behind the oven shell for all these 17 years. Inspection of this wire showed it carried 115V. I wrapped this wire with electrical tape and reinserted it into the insulation behind the oven shell.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alyce from Littleton, CO
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler element burned out
The customer service at PartSelect.com is wonderful. They assisted me to located a part for a 40 year old oven. Took only a few minutes to take the old one out and put the new one in. Process was pretty self explanitory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEVIN from WAUSEON, OH
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Oven element was shorted out
No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few seconds element got hot, job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Raleigh, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven took long time to reach desired temp. Element sparkled and burned up.
First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the oven on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Franklin, TN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
old heating element burned out
unplugged oven. removed oven racks.Disconnected old unit. Installed new unit. Very very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Seagoville, TX
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
element burned out
Could not believe how fast the part shipped. 2 days and it was here. All it took was using a nut driver to remove 4 screws and then put the new one in.
Was this instruction helpful to you?
Thank you for voting!