JBS07PIY3 General Electric Range - Instructions

While I appreciate all the various parts available from PartSelect, I was disappointed that the only heater element that was approximately the right size and shape for my wall oven had push-on prongs. My original was screw-on.

Thus, I had to (very) carefully drill through the somewhat thick metal tabs to get screws into them. This meant holding the tabs with a pliers while I drilled them out to make sure that I did not break off the tab. Then, I increased the hole size by using increasing diameter drill bits. I let the screws self-tap, but again this was done carefully to avoid breaking off the tabs. Finally, I found that the part of the new heater element going through the back wall of the oven was an inch or so longer than the original. This did not seem to cause a problem of overheating outside the oven. At least not so far!

I pulled out the old burner - put the new one in and I was done. No tools required.

The first burner I received from PartSelect was warped. I called on Friday morning to see about returning it and ordering a new one. The CSR was very helpful and I was totally surprised to have the replacement arrive the very next day since I didn't ask for a Saturday delivery. I will definitely use PartSelect again.

I am not going into a description. It is a very minor thing to do. I did appreciate the quick delivery of the parts and will purchase future appliance parts from you again.

popped the new one on!

Of course the first thing is to turn off the breaker, Unplug the appliance, pull the two electric feed wires off the old element. Then remove the four screws that hold the fan guard in, After that the two screws that held the Bake Element in place. Then reverse the process to install the New Element. Took about twenty mins. from start to finish. Just Like New. And thanks to Parts Select for their prompt service, Had the new part in two business days.

Did it By Hand
Your Shipment Time Excellant
Order it Mon. Received it Wed.


Thank You

It was so simple looking, I had it shipped to the tenants of the house. They swapped it out easily, and were happy to get back to baking.

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.

Just removed the elements and inserted the new drip pans. Could not have been easier.

saw when heating the stove up the bottom element wasn't getting hot. got part number and looked up online and ordered

First I shut off the power at the power box. Second I removed two screws in metal plate. Third I unplugged the two wires. Repeated steps backwards and it works great.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Removed old, and replaced with new, heating element! Maybe 10 seconds.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the the two screws that connected the wires and element together. I then tried to connect the new element to the wires, but found that the screw holes were smaller than the original holes in the old element and the original screws wouldn't fit. No problem, I then got a cordless drill and found a drill bit a little bigger than the holes, I held the element connector with pliers and made the screw hole a little bigger, same with the other connector. I screwed the screws into the connectors with a socket wrench and then screwed the element back into the holes in the oven, then turned on the oven and it works as good as new.