JKP18G4K2 General Electric Range - Instructions

took the element screws off, a little bit dificult to fine the small wrench socket to disengage. I had to have my husband do it because I have too short arms.
I can't believe how much money we saved., the part was there within two days and installed, for a total of 52.00 including next day Fed ex.
Feel good about the whole expierence.

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

Replacing the electric oven element was easy. It took about 20 minutes and all you need is a screwdriver and a pair of pliers. What you have to do first, turn the power to the oven OFF. Remove the original element carefully observing how
it was installed and install the new element in the same order.
I have used Parts Select a couple of times in the past years and the delivery came quicly without any problems.

Spyro.

First I turned the power off to the oven. Then I tried to take out the nuts holding in the element. One nut came off easily, the other one was rusted on, I had to use wd40 to loosen it. The project was easy once I got that nut off. I pulled out the element, which is connected to two wires. I took those screws out, connected the new element to the wires, re-attached the screws, pushed it back in, attached the nuts that hold the element in the oven. Then I turned the power back on and the oven works like a charm. I installed it the day I got it. I was surprised how quickly it was shipped to my house. I am so glad I repaired the oven, a new one would have cost over $800, I bought the element for less than $30, including shipping! It also sets a good example for my daughter. It taught her that her mom can repair things too, it's not just something men can do!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and made sure that there was no power feeding the element. Next I disconnected the two wires that power the element. I then removed the old element and replaced it with the new element. Tightened the screws but had to be careful on the second one and hold with plier as the first one bent a little as it was being tightened. Slid the element back after the connection screws were tightened and tightened the mounting screws. Reenergized and tested. The job went well - easier than expected...

Turned breaker off to oven. Removed 2 screws from burned out element in back of oven and pulled it out. Installed new element and tightened the two screws. Very easy.

My oven is 31 years old so was suprised I could still get parts.

Unscrewed the broken element from the back of the inside of the oven, then unscrewed the connected wires from the element and did the reverse with the new element. Viola.

Before touching anything, however, I made sure the oven was in the off position and also went to the house circuit breaker box and flipped OFF the appropriate circuit breaker(s). There were two - one for the element and another for the rest of the controls.

When everything was in place, I turned the power back on and turned on the oven and was cooking again. We had Prime Rib for Easter.

I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.

Took the old one out and replaced with the new one. It was just awkward to get at.

New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in same position. If we had called a eepair company it would have taken a week or more and probably been expensive!

husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.

I read your website repair testimonials by previous customers and used that advise to do the job. I liked the suggestion to use something to attach to the unattached wires so they don't slip back into the unit. I used two clothespins. I had one stubborn electrical connection to disconnect so it took a little longer -about 30 minutes. But it was a simple job to do and my oven works fine again. The item was delivered timely from the order date and packaged well. Thank-you!

shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!

On thanksgiving day, as we were pre-heating the oven, electric sizzle, sparks and a little flame comes from our 24 year old oven. We were able to get dinner on the table and that evening I went looking for what I thought was going to be a difficult to find part. But I found the part on partselect. I ordered that evening and got it on saturday. Installation was a snap. The most difficult part was the nuts holding the wires were stuck on from time and heat and I worried about the wire from the small plate to the coil might break. A little wd-40 and a few minutes and they popped right off and right back on. Works great now.