JGBP24BEH5WH General Electric Range - Instructions

I just lifted the old part and dropped the new one in. Everything fits perfectly. The new flame is a beautiful blue color.

We bought our replacement burners from Part Select.com at half the price of another major appliance store. They came fast & fit perfect. All around, we are very happy.

just lift the cover and put it on.less than 1 minute.

The key here was that I found the correcd part for an older kenmore oven and it was easily installed

matched part needed on web site; took off burner; ordered part; received it on the third day and easily replaced it. Wonderful, easy, and very short delivery time! Thanks.

I had to replace the ignitor. The wiring was simple. Just had to connect two wires. The difficult part was removing and replacing the ignitor. It is suspended by 2 screws that are very difficult to access.

Troubleshooted ALL possible causes and after perusing the owners manual and PartSelect blogs. Can't say it enough, people!! Do your homework- there are 3 possible parts that can cause the oven not to light; Igniter, gas safety valve, or thermostat / power switch assy (oven control knob).
SAFETY FIRST...UNPLUG the stove before performing any of the following electrical circuit checks (besides voltage check, which is ONLY for those qualified for electrical circuit maintenance)

Remove oven door by opening slightly and pulling straight up- it will slide right off the hinges.
Remove the 2 thumb screws holding the lower oven plate and slide it toward the back while lifting up on rear of plate to clear the front flange and then remove the plate.
The burner tube baffle plate will come right off after removing the one retainer screw (1/4" nut driver).
(Optional)Remove the whole broiler drawer by sliding it fully open and lifting it up by the front end.
Now you'll have clear access to the igniter, which is mounted on the rearward end of the burner tube with two 1/4" machine screws. Disconnect the igniter wire connectors at the gas safety valve and wire harness. Remove it and SAVE the screws for mounting the new igniter!! NOTE: .
Handle the new igniter CAREFULLY!! (don't drop it or bang it against anything solid or the heating element will break).

1) Checked t-stat switch on oven knob - good (closed or 0 ohms when turned on). This verifies you are getting supply voltage to the igniter circuit. Lift the oven top by the front corners until the supports lock into place. Locate and disconnect wires on back of switch and measure ohms across switch terminals.
2) Checked voltage at igniter wire terminals with oven knob turned on (this step ONLY for those familiar with proper use of multimeter and training for electrical circuit maintenance). This verifies the gas safety valve switch is closed and correct voltage is available to power the igniter (120V).
3) Since I had proper power to the igniter wire terminals with the oven knob turned on past 200 deg., that verified a malfunctioning igniter.
4) I chose to solder and heat shrink the wire connectors to the new igniter but you can use the supplied ceramic wire nuts. Be sure to leave enough wire length when you cut the wires off the old igniter. Mount the new igniter to the bracket with the screws you saved and be sure to snug them good but DON'T overtighten and strip the threads!! Connect the two igniter wires to the gas safety valve terminal and the harness connector. Make sure the connections are snug!!
5) Reinstall the burner baffle plate and lower oven plate.
6) Remount oven door and turn on oven past 200 deg. The igniter element should glow bright red after a few seconds. Gas valve should open and burner will light a few seconds later.
NOTE: Make sure the gas cock for the oven (on the side of the main gas regulator valve) is flipped to the open position or gas will not flow to the oven burner. The main gas regulator valve is located under the range top toward the rear (trace the gas lines if you can't locate it readily)

I removed the igniter by first removing the oven racks then the oven pan and oven catch pans. I open the lower draw to the oven and removed the drawer. I reached back under the oven and clipped the wires that run to the igniter and striped a half inch of plastic to expose the wire. I removed the igniter from the burner and replaced with new igniter. I then fed the wires back through the hole the cut wires came out of and used the wire nuts supplied to connect. Replaced other parts in reverse order and tested. Works great.

I removed lower drawer, removed oven door,
took out rear screws to oven pan,removed screws that attatch ignighter to oven wall,disconnected wiring and removed old ignighter. reversed process to install new part. total repair time was about 20 minutes. Also take into consideration that i am a building contractor familiar to appliance repair etc.

First had to disconnect the old igniter by removing screw with a small wratchet wrench. Then pull out approximately 3" of wire from the old igniter, cut off old igniter, attache replacement igniter with supplied wire nuts, shove excess wire back into wiring compartment and then attach the new igniter.

pop up range top. pull off old burner. put on new one.
close top. check for rocking. install leveling washer. check again. 2nd burner didn't require leveling so it was quicker.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

The repair was easy and not very time consuming. It didn't take very long to fix the problem and thanks to this site, I was able to save the money I would have spent if a repair technician came out to do the same work. Now I can afford Christmas and cook too!

1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy

Good friend said he could do it no problem at all!!!!!