J797002 General Electric Range - Instructions

removed old element rewired new element,turned back on power

Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.

These two repairs were straight forward and the repair does not need elaboration. The amazing aspect of this repair was that I ordered my parts and received them on the second business day without any additional charges. That was really fast ! Thanks Partselect.

disconnected power
remove oven racks and oven bake shields
removed two bolts from end bracket plate on element
carefully pull bake element partly out until the electrical wires are visible, remove two small screws, remember the side of element each wire
attaches, red is power black is ground.
, replaced new element in reverse order, reattach wires to element and snug tighten , not over tighten. Element worked
like new.

First my husband removed the screws that held the element in place, pulled it partially out and then disconneted the wires. He located the part number that was stampted on the defective element and then I searched the internet for GE parts. I noted the price at GE site and continuted to search. The PartSelect price was about 1/2 of the GE price. We ordered the part, it arrived in two days, and we replaced it in less than 30 minutes. We were very pleased.

Turn the power of to the stove used a 5/16 socked and unscrewed the element from the stove. Used the socket to remove the wires from the element. Installation was easy make sure you hold the end of the elements where the wires attach so they do not bend when tightening. Everything is working and back to normal. Make sure you use the model number to get the correct part needed.Part select was the best and delivery was with in 5 days.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

There was no burner listed like 40 yr old burner that failed. Got one the same size and connections. Cut old burner out of the stainless steel ring and new burner fit right in. New burner works great

Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.

Repair is pretty easy, its the accessability that makes it difficult. This is a wall mount oven. Removing the door would provide pretty good access, but having to reach over the door into the very top back of the oven is a real pain (in the back and other places). As another customer said, there were many dropped screws and much cussing. The old element terminals were just holes in a metal tab that accepted tapered screws. The new element had terminals that were threaded to accept the screws provided. It took lots of twisting and turning of the element and the power wiring to get the terminal on the wire lined up with the terminal on the element in a position where I could hold them together and insert the screw and start the threads. Don't try this after you've had a beer or two. Whew!!! Many tries, sore back, but did it. Like I said, simple except for the reach. Bake element was much easier. Hope I don't have to do this one again. My GE oven is a winner (20 plus years old) and Parts Select has what you need at a reasonable price and ships quickly. Have used before and will use again, if needed.

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

Asked a local repairman to fix it. I saved money(saved $20.00) by ordering the broiler element from GE part select via customer service agent. The agent was informative and helpful. The part arrived the next day even with regular shipping cost. Impressed with the GE part select. Will use the company again.

I am left handed which sometime presents things in a aweward way. My greatest task was finding the right position and being able to hold the leads while trying to connect them. So I got a pillow and positioned myself and got into the oven and was able to do the job from there. After doing so, it took about 10 minutes to do the replacement.

It would have been easy, but the screws that came with the replacement burner were too long for the ceramic insulator to fit over. Had to grind down the screws fro 3/8" long to 1/4" long. After that, piece of cake.

We unscrewed the element easily enough, but had a hard time disconnecting the prongs. Once we did, we had to use a thin screwdriver to open the clamps to fit the new prongs into them. After all was accomplished and we switched on the breaker the broiler still didn't work. Either we did something wrong or the element wasn't the problem. We haven't decided our next move yet; whether to get a repairman in or buy a new oven. It's a pretty old oven/range.