JKP40G2K2 General Electric Range - Instructions

Removed 3 screws from cover {center of back side of oven}, removed 2 screws from wires connected to element, then removed 2 screws mounting element
{inside oven}, pulled it & replaced it.

Part was in stock, delivered in two day, Wow!!
First shut off power to the oven, the removed the two screws that held the element in place, pulled the old one out and disconnected it and put the other right back in. took less than 1/2 hour.
Very satisfied with product , easy of repair and especially the price and delivery.

I removed the two screws that keep the element in place.Then I pull the element a little bit and disconnected the two wires and removed the old element. Then I reconnected the two wires on the new element then put the element back on position and put back the two screws that keep the element in place. Done.

Repair was easy! I asked my son to take out the old and put in the new! He did! The oven works like new again for less than $50.00!!! Thanks!

I removed the plate held by 2 screws that holds the element, pulled the coil out and disconnected the yellow and red wires. Removed the broken one and connected the new one. Very simple. I also would like to add that you people are great to deal with and I will tell everyone to buy parts from PartSelect. Your service is outstanding and fast. Thank You.

No instructions provided, but not needed. Removed two screws holding element in place. Removed two screws connecting element to power wires. Installed new element using reverse process.

Safety first! Flipped breaker for oven in main breaker box.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.

Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.

Removed two small bolt screws that held the bottom burner in place. Unscrew the two small screws that attach the oven wiring to the bottom burner. Put the bottom burner back in place and screw the two small bolt screws back in and its done.

Removed burn out element,very easy to installed, screwed them in, done that fast!

Ordered the part on a Friday afternoon and was shocked to receive the box on Saturday AM! Turned off the power to the unit, unscrewed the screws holding in the old element, and hooked up the new one. We didn't have a socket wrench so we subbed a pliers. So easy & cheap! Seems like everything's breaking around this house & this is the ONLY thing that was easy & cost less than $20! Happy with Parts Select!

unscrewed the broken one and replaced it with the new heating element. Worked perfectly! 20+ year old oven.

Unscrewed old element and screwed in the new one.

so easy it doesn't need an explanation. Just remember to throw the breaker switch before beginning!

1) Turned off breaker and verified that the oven would not turn on. 2)Removed racks from the oven. 3) used nut driver to remove two mounting screws 4) used screwdriver to disconnect bake element from the wires. 5) used supplied screws to attach wires to new bake element. 6) pushed bake element into place and used nut driver to secure it in place with screws. 7) replaced racks 8) turned on breaker 9) tested by turning on oven with oven thermometer in place.