YEK735WP5WG General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DANNY from GROVE CITY, OH
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
element was bad, not heating
had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Orlando, FL
- Parts Used:
- WB2X9719
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Clips needed to re attach heating element
Pulled out old with pliers. Twisted new clips in per instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Munt Laurel, NJ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Probe broke
Ordered new probe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Decatur, IL
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element melted down
Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.
Was this instruction helpful to you?
Thank you for voting!
Burned-out Element
First of all, go to circuit breaker box and switch off the power to the oven.
Return to oven and verify the power is definitely off.
Open oven door to 'vent' position and remove door. Return hinges to closed position. Remove all racks.
Using nut driver (1/4-inch) remove the two screws just above the element.
Gently rock the element back and forth while pulling gently toward yourself. You should see two wires emerging from the layer of insulation in back of oven. When you have enough wire exposed, use long-nose pliers to gently rock the 'Faston' connectors and pull them off the element's male connectors.
Insert new element and re-install the connectors, being certain they are fully engaged.
Fasten the new element to the back wall of the oven using nut driver. Be careful to not cross-thread - gentle is the word!
Turn the circuit breaker on and very briefly turn the oven to Bake and verify the element is heating. It likely will smoke a bit.
Re-install the racks and the door. Reset the clock.
You should be done and your oven should run for many years..
Return to oven and verify the power is definitely off.
Open oven door to 'vent' position and remove door. Return hinges to closed position. Remove all racks.
Using nut driver (1/4-inch) remove the two screws just above the element.
Gently rock the element back and forth while pulling gently toward yourself. You should see two wires emerging from the layer of insulation in back of oven. When you have enough wire exposed, use long-nose pliers to gently rock the 'Faston' connectors and pull them off the element's male connectors.
Insert new element and re-install the connectors, being certain they are fully engaged.
Fasten the new element to the back wall of the oven using nut driver. Be careful to not cross-thread - gentle is the word!
Turn the circuit breaker on and very briefly turn the oven to Bake and verify the element is heating. It likely will smoke a bit.
Re-install the racks and the door. Reset the clock.
You should be done and your oven should run for many years..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Coal Creek, CO
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The range kept giving an F2 alarm
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Franklin, NC
- Parts Used:
- WB44K5009
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Broil element burned out, literally!
Turned off power to oven. Lifted off the oven door. Removed four 1/4 " bolts from outside of fan housing. Removed two 1/4" bolts holding element. Removed element from three clips holding it to upper oven surface. Unplugged two element wires. Reassembly was the reverse. I am an auto mechanic by trade and this was a fairly simple process.
Was this instruction helpful to you?
Thank you for voting!