JKP07007 General Electric Range - Instructions

Turned off the breaker. Removed 2 screws and pulled the element from encasement. Removed 2 screws holding the wires to the element.
Reversed the process to install the new coil.
Done in 10 minutes

Unscrewed face plate, unscrewed electric wires hooked to element. Cleaned out oven while I was in there...nice and clean now. Installed new element same way I took it out. Easy as 'pie'..which we'll be baking again now that the oven works.

The repair was a snap! Unscrew the two small bolts holding the back of the element in place. Pull out the element so that the connectors and wires are accessible. Unscrew the two wires from the element. Remove old element. Place new element in oven. Attach the two wires to the new element (two screws), place the new element in position and replace the two small bolts that were removed at the beginning. All done. Best thing? This is a 20 year old oven, GE didn't even have the part I needed. You did! Thanks.

Looked up mfg. and part #,looked at blow up of stove on parts select, identified element. The part came overnite. Shut down power, removed 2 screws with a nut driver, pulled element foreward to reveal 2 screws attaching wires. Replaced in reverse order, turned on power, back in service. 10 minutes tops.

It is simple.

Cut off the power. Remove racks. Remove burned out element and replace with new one.

Replace racks and turn on the power. Set the clock.

I've done this about 5 times and now keep a spare element.

IT was fast and easy! Thanks

Removed old part, install new one.

Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!

I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.

I pulled it out a bit and exposed where the element screws into the power.

To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.

After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.

Reset the breaker, and you're good to go.

Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.

Turned off power at breaker and removed old element and replaced new element.

removed old element and installed new, and oven is up and working like new

Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.

After checking the website, I wasn't sure the part I needed was available. Called the Customer Service number and the lady was very helpful.
My part was delivered in 2 days regular UPS.

The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.

removed the element with 2 screws. disconected element with 2 screws. reversed order to install new element.

Shopped online for a good price for the heating element. Thw element came very quickly, very good packaging. Removed and replaced the element.