JDP36BW1WH General Electric Range - Instructions

Removed nuts holding element to rear of oven using nut driver, pulled wires out 3 inches and disconnected using needle nose pliers, installed new element. Job took 10 minutes - very easy job and works fine.

Very easy repair. Part came wrong the first time (my fault for ordering the wrong one). Called and ordered the correct one after a closer match to the original part. Delivered much quicker than promised (one day) and installation very easy. Will use this site for all future repairs.

orderd a replacement part. recieved it two days later then that evening installed it. there was a video online to show how to replace it. very useful if your not a do it yourselfer.

I went on-line, found Partselect.com, they gave me the part number, showed me a video on the repair details, shipped the part overnight, and within ten minutes of the arrival of the part, I was up and running. EXCELLENT SERVICE! Thanks for saving Christmas at our house!!

You literally saved our Christmas from a disaster! Four days before Christmas our bake element gave out and we discovered it had split. We found you on the Internet, ordered the part, and prayed you would deliver as promised. We received it the next day, as promised, and in time to cook Christmas dinner. It was a snap to install, literally took five minutes. Your service, response time and instructions were perfect. Keep up the good work!

Well...you'll notice in other tools I put Tweezers. Now you really don't need tweezers if you do it right in the first place. Here's what I did: 1) unscrewed the nuts that hold the element in on the back of the unit. 2) Then pulled the terminals out of the holes in the back of the oven. OOPS...there were sparks as the right terminal wire hit the metal frame of the back of the oven. Scared me. I jumped. the terminal wire burned/broke off and fell back into the hole. Yep...Too late I remembered that the VERY first step of this repair is 1)CUT OFF THE POWER TO THE OVEN. I repeat...THE FIRST STEP IS TO CUT OFF THE POWER TO THE OVEN. I couldn't reach the wire with the needle nose pliers so I had to go get the tweezers. Couldn't see the wire but I just put the tweezers in about two times and it finally caught on the wire and I was able to pull it out. Luckily the terminal end was still connected to the wire so I didn't have to replace it. From there it was 3)remove the old terminal posts from the wires (used the needle nose here to wiggle the ends off - been on a long time), 4)insert the new ones, 5) push the terminal posts back in the holes, 6) screw the nuts back on, 7) bake the cornbread. A very quick job -- plus the element from PartSelect was almost half the price of any other I found (due to this I was able to upgrade the shipping a little to get it sooner and still saved money over any other price I found. Just remember to CUT OFF THE JUICE BEFORE YOU START this repair and it will be done in 5 mins or less.

I actually don't remember if instructions came with purchase. I have purchased appliance parts from here before and they did on previous times. I watched a couple of YouTube videos because I'm a visual guy (as I think most guys are) and the only difference between my reality and the video was I had nuts holding the element in place and the video had screws holding it in place. Extremely easy!! TURN OFF POWER TO STOVE.....PLEASE. Confirm power is OFF (clock not working...range wont turn on....something like that) Take oven door off hinges (mine just slid off without any problem). Remove defective element from oven. In the back there are two screws or bolts, take them out. SLOWLY pull old element out. Be careful and look for the insulation that will try to come out of the hole and watch for the wires that are attached to the element. The wires will come out far enough for you to work with them (about 6" or so). Be very careful NOT to jerk wires through holes too much or damage them. Remove wires from element. I used two pliers, one on element and one on wire crimp...I also sprayed wd40 on the connection prior and let it set for a short time before to loosen it up. Once separated, discard old element. Get new element and reverse the process. I reconnected wires, making sure to put them back in the exact same side they came off of. Ease the element power prongs back through the holes (VERY CAREFULLY, DON'T RUSH AND TEAR IT UP). The new element will fit exactly where the old one came off and just put the screws or bolts back in place and be VERY CAREFUL NOT TO STRIP THE SCREWS OR BOLTS. Turn power back on at breaker and turn on oven to check and see that it works. It should work great. This is the second part I've purchased from these guys and both jobs went flawlessly. I HIGHLY RECOMMEND these guys...plus it's almost the only place I could find to get the parts, but still they are great.

After noticing it needed replaced I went to PartSelect, put in model/serial# and order that easy. It was here the next day. The oven was fixed. Now back to baking...thanks PartSelect.

I really like my repairman, but prefer to do it myself. PartSelect rocks...reasonable prices, really fast shipping AND online repair videos keep me coming back. The repair was exactly as the video described, but one of the wires came loose as I was pulling the element through. I thought I'd have to tear the stove apart to get to it, but luckily, all of the wiring is contained in a raceway that runs along the back of the stove. After removing it to expose the wires, I would recommend doing so instead of trying to pull the wires through as the video shows. In doing so, the terminal connections are readily accessible and it's much easier to remove and install the bake element without having to worry about feeding the wires through at the same time and running the risk of damaging them. Overall, a very simple, quick repair that saved me a $50-75 service call.

the only challenging thing realizing that the screws in the back weren't for a screw driver, they were for a very small wrench. Since I didn't have such a tool, I just used vice grips. It all went well though. The oven currently heats to 400 degrees in 7.5 min. I am quite happy.

Removed the two screws pulled out the old element and slid the new element in and put the screws back in. I used it that night to bake supper

Turned off circuit breaker for Range. Removed the 2 screws holding element and pulled wires attached to the element through holes. Disconnected the wires and attached new element. Had problem with one wire springing back into hole used paper clip to fish it back out of hole and then connected 2nd wire to heating element. Turned breaker back on and tested. Baked a cake. MMMMMMMM.

I read the "easy to repair" story after I ordered my part and I felt like I coud do this on my own. (Female not much experience in repairs) I shut off circuit breaker...proceeded to take out element...could not get it to easiler come off...so I made the mistake of cutting the wire because it looked like that's what I needed to do. WORD TO THE WISE...there are clamps that actually pull off the element..just need to pull a little. So my "easy" project was made more difficult because I didn't know this up front. Otherwise it would have been a breeze. I had to go to the hardware store and but new clamps and attach to the cut wire. Good news is my oven is now working and Parts.com was fast, cheaper than the GE parts place and great service.

Removed the two screws and pulled out the bake element. Then plugged in the new element and replaced the screw. Easy

After watching the video on your website the repair was a cinch. I would never have attempted doing it if I hadn't seen your video. Thanks for saving us a lot of money.