JGBP26WEHW General Electric Range - Instructions

Diagnosed the problem as igniter failure and called local parts outlet. They gave me the part number, but said they were out and directed me to another vendor. When the part came, it was the wrong shape but I tried it anyway. Result - the igniter glowed which allowed the gas to flow, but igniter, being the WRONG PART, didn't ignite the gas, allowing a dangerous build-up of gas.

I then went to PartSelect, looked up the part, saw it was the correct one, ordered it (arrived within 3 days) and, because I already had the pans and covers off the oven, it was a matter of minutes to install. Works like a charm and, though I usually like to buy locally, I'll check out PartSelect first next time!

I removed the 2 screws that held the bottom oven plate in place. Then I removed the one screw holding the bottom burner in place in the front. I then reached into the rear area and unscrewed the last 2 screws securing the burner. I disconnected the igniter wires at their push-on connections and lifted the whole burner/igniter unit out. I relaced the igniter using the 2 attachment screws, and I cut the old igniter's wires with connectors and spliced them into the new igniter's wires, using the ceramic wire nuts that came with the new igniter. I reassembled the unit and it worked first time.

Checked on this website for ideas. A 20+ year repairman posted that the problem is the control valve and I should replace the igniter while I'm there. The valve was priced at $189 and the igniter $60. I decided to try the igniter first and all is well. Valve not needed.
Steps; remove; door, lower tray, and oven floor pan. Disconnect two igniter wires. Use 6mm sock to loosen gas feed tube, then lift tube up a couple of inches to access igniter screws. Remove them, and reverse process with new part. I tried to R&R the igniter without loosening the gas feed tube but it's a real PITA. Good luck, easy fix.

Ignitor is easily reached by removing the bottom of the oven floor. Machine screws remove easily when appliance is relatively new, but from experience, they may give you some trouble when stove is 5+ years old! Our part came in a timely fashion, even when ordered over a holiday weekend . Replace ignitor just as the old one came out-one word to the wise...scrape off enough silver coating on the wires so that a good contact is insured before splicing with the wing-nut included. Having had many GE stoves, I notice that the factory-installed ignitors have a shorter and shorter life; I'll be keeping PartSelect's website handy!

Following the recommendations of others I decided to attempt repairing the oven by myself. I unplugged the stove. I removed the oven door, the drawer, the drip pan from below the oven unit and the oven pan to access the igniter bracket. All screws were 1/4" hex head except the oven pan which were slotted. I disconnected the 2 wires. I removed the old igniter and cut the 2 wires close to the old igniter to allow extra length to splice to the new igniter. The new unit included 2 wire-nuts. It was simple to wire-nut the new wires to the old ones and install the new igniter. I reassembled the pans I had removed and the door. I plugged the stove back into the wall. The new igniter worked perfectly. My wife continues to tell me how great it is to have a working oven again and how much faster it seems to heat. I am thankful the oven didn't fail while we were cooking the Thanksgiving turkey the week before. I debated calling a repair technician or shopping for a new stove. The price of the new igniter and the description of the procedure convinced me to attempt a repair. I am very pleased with the results.

removed bottom of oven.removed heat shield.i
then unscrewed the wire nuts to the igniter.i
then tookout the burnner with the igniter attached.
i unscrewed the two screws holding the igniter
in place,and put the new one on.i then screwed
the wire nuts back on,and put it back togather.
it works great,thanks for the help.it saved me alot
of money.

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.

Go to utube videos for this are there

Straight forward as per instructions. Removed old igniter, replaced and tested new one and it worked. However, the gas oven would not turn of. Valve may be defective. Knob control is not stripped and turned to full stop. Troubleshooting continues. Part(s) and instructions worked perfectly.

i went for 3 months waiting on the electrician who never came then asked the plumber who else could fix it and he said my husband could it only needed to unscrew 4 tiny screws and unplug and cut and twist wires back the hardest part was reaching the bolts hooked to the ignighter the burner was in the way and is not as easy to remove as someone has said all in all it saved us 100 dollars and could have saved us months of burning food trying to cook on broil if i had only called the plumber first.ha ha

- removed the oven unit from the wall
- removed the aluminum backplate to expose the wiring
- Removed both glass wire nuts and disconnected the heating element\
- From the front, I removed both retainer screws and pulled the element wires through.
- In reverse order I reinsalled the new wires and screwed on the heating element.
-I reattached the electrical wiring and rear pane.
- I re-installed the unit into the wall.

Simply removed old burners. Placed leveling nuts in place. Replaced new burners in place.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

Simply took out old burners replaced them with new burners, no tools needed.